Memory Seat Feature Inoperative
Memory Seat Feature Inoperative
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The memory seat switches are normally open and are wired to the driver window switch. When a memory recall switch is pressed, the switch pulls the 5 V signal circuit from the driver window switch to ground. The driver window switch senses that a memory recall signal is pulled low and a serial data message is sent to the memory seat module (MSM) identifying the memory request. The MSM responds to the request by commanding the driver seat to move to the preset positions.
Diagnostic Aids
The memory seat module is also referred to as the Driver Position Module in certain scan tool menus.
Reference Information
Schematic Reference
Driver Seat Schematics (Driver Seat Schematics)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Memory Seats Description and Operation (Memory Seats)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the memory seat adjuster switch.
2. Test for less than 5 Ohms between the ground circuit terminal C and the ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Memory Recall Switches parameter is Idle.
• If not the specified value, test the appropriate signal circuit listed below for a short to ground. If the circuit tests normal, replace the driver window switch.
* Memory 1 terminal A
* Memory 2 terminal B
4. Install a 3 A fused jumper wire between the signal circuit terminal A and ground. Verify the scan tool Memory Recall Switches parameter is Memory 1.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the driver window switch.
5. Install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool Memory Recall Switches parameter is Memory 2.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the driver window switch.
6. Install 3 A fused jumper wires between both signal circuit terminals listed below and ground. Verify the scan tool Memory Recall Switches parameter is Exit.
* Memory 1 terminal A
* Memory 2 terminal B
• If not the specified value, replace the driver window switch.
7. If all circuits test normal, test or replace the memory seat adjuster switch.
Component Testing
Memory Seat Adjuster Switch
1. Ignition OFF, disconnect the harness connector at the memory seat adjuster switch.
2. Test for infinite resistance between the ground terminal C and the signal terminals listed below with the switch in the open position:
* Memory 1 terminal A
* Memory 2 terminal B
• If not the specified value, replace the seat adjuster switch.
3. Test for less than 1 Ohms between the signal terminal A and the ground terminal C with the memory 1 switch in the closed position.
• If greater than the specified range, replace the memory seat adjuster switch.
4. Test for less than 1 Ohms between the signal terminal A and the ground terminal C with the EXIT switch in the closed position.
• If greater than the specified range, replace the memory seat adjuster switch.
5. Test for less than 1 Ohms between the signal terminal B and the ground terminal C with the memory 2 switch in the closed position.
• If greater than the specified range, replace the memory seat adjuster switch.
6. Test for less than 1 Ohms between the signal terminal B and the ground terminal C with the EXIT switch in the closed position.
• If greater than the specified range, replace the memory seat adjuster switch.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Driver Seat Adjuster Memory Switch Replacement (Removal and Replacement)
* Control Module References (Programming and Relearning) for driver window switch replacement, setup, and programming