Head Up Display Malfunction
Head-Up Display Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The head-up display (HUD) is a secondary display system capable of reflecting important vehicle information onto the windshield. The vehicle information is displayed using virtual imaging and is reflected on the windshield in front of the driver. Battery positive voltage is the power source to the HUD system. The HUD system can only be enabled when the ignition is active and in RUN position. The HUD receives vehicle information for display via the serial data circuit. The HUD system also receives vehicle and engine speed information via discreet vehicle and engine speed signal circuits. The HUD interfaces with the HUD switch via discreet circuits and the HUD switch inputs to the HUD is low. A press and hold of the dimming up switch initiates a smooth increase in the HUD display intensity until the switch is released or maximum intensity is achieved. The HUD does not have a separate Off switch. The HUD is turned OFF using the dimming down switch. A press and hold of the dimming down switch initiates a smooth decrease in the HUD intensity until the switch is released or the HUD is turned OFF.
Reference Information
Schematic Reference
Head-Up Display Schematics (Head-Up Display Schematics)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Head-Up Display Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information.
Circuit/System Verification
1. Ignition ON, verify that when the HUD dimming up switch and the HUD dimming down switch are pressed, the HUD display intensity and the HUD scan tool Dimming Level Percent parameter increases or decreases as each switch is pressed.
2. Verify that when the HUD switches are pressed and released , the HUD scan tool switch parameters toggle between Active and Inactive.
• If the switch parameters do not toggle between Active and Inactive, refer to HUD Switch Malfunction.
Circuit/System Testing
HUD Inoperative
1. Ignition OFF, disconnect the harness connector at the HUD.
2. Ignition OFF, test for less than 5 ohms between the HUD ground circuit terminal 6 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the HUD.
3. Ignition ON, verify a test lamp illuminates when connected between the B+ circuit terminal 1 and ground. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the HUD.
4. Ignition ON, verify a test lamp illuminates when connected between the HUD dimming up switch signal circuit terminal 11 and B+ while pressing the HUD dimming up switch.
• If the test lamp does not illuminate, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the HUD switch.
5. Ignition ON, verify a test lamp illuminates when connected between the HUD dimming down switch signal circuit terminal 12 and B+ while pressing the HUD dimming down switch.
• If the test lamp does not illuminate, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the HUD switch.
6. If all circuits test normal, test or replace the HUD.
HUD Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the HUD switch.
2. Test for less than 5.0 ohms between the HUD switch ground circuit terminal F and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that all scan tool HUD Switch parameters are Inactive.
• If any are not Inactive, test the signal circuit terminals listed below for a short to ground. If the circuit tests normal, replace the HUD.
* Page switch signal terminal H
* Image up switch signal terminal J
* Image down switch signal terminal K
* Mode switch signal terminal G
4. Ignition ON, install a 3A fused jumper wire between the HUD switch signal circuit terminals listed below and the ground circuit terminal F. Verify that all scan tool HUD switch parameters are Active.
* Page switch signal terminal H
* Image up switch signal terminal J
* Image down switch signal terminal K
* Mode switch signal terminal G
• If any are not Active, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the HUD.
5. If all circuits test normal, test or replace the HUD switch.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Control Module References (Programming and Relearning) for the HUD replacement, setup and programming
* Head Up Display Switch Replacement (Head Up Display Switch Replacement)