C0710
DTC C0710
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C0710 00
- Steering Position Signal Malfunction
DTC C0710 42
- Steering Position Signal Calibration Not Programmed
DTC C0710 5A
- Steering Position Signal Not Plausible
DTC C0710 71
- Steering Position Signal Invalid Data
Diagnostic Fault Information
Circuit/System Description
The steering angle sensor receives a 12 V reference voltage from the electronic brake control module (EBCM). The EBCM receives high speed controller area network (CAN) message inputs from the steering angle sensor identifying the position and direction of the steering wheel rotation. The EBCM utilizes this signal to calculate the driver intended driving direction.
Conditions for Running the DTC
Ignition ON.
Conditions for Setting the DTC
C0710 00
The steering angle sensor signal is invalid.
C0710 42
The steering angle sensor is not calibrated.
C0710 5A
* The steering angle sensor signal is out of specified range.
* The steering angle sensor offset is out of specified range.
C0710 71
The steering angle sensor signal is not plausible with the yaw rate sensor signal and lateral acceleration sensor signal.
Action Taken When the DTC Sets
* The EBCM disables the stability control for the duration of the ignition cycle.
* The traction control/stability control-active indicator turns ON.
Conditions for Clearing the DTC
* A current DTC clears when the diagnostic runs and passes.
* The EBCM will turn OFF the indicator in the next ignition cycle.
Diagnostic Aids
* Confirm that all tires are of the proper size and that all are matching brands. If a mis-sized or non-matching brand tire is present, inform the customer that in order for the vehicle stability enhanced system to function normally, tires need to be a uniform size and rolling diameter.
* Check and adjust all tires to the stated cold air pressure as identified on the tire placard.
* The car should not pull in either direction causing the steering wheel to be OFF center while driving in a straight line on a level surface.
* Improperly mounted or loose sensor.
Reference Information
Schematic Reference
Antilock Brake System Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
ABS Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Steering Column Position parameter. As the steering wheel is turned, the reading should travel between -550° and 550°.
Circuit/System Testing
1. Ignition ON, verify that DTC C0710 is not set.
• If DTC C0710 is set, perform the Steering Angle Sensor Centering (Procedures).
2. Ignition OFF, disconnect the harness connector at the B99 Steering Wheel Angle Sensor.
3. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 10 ohm between the ground circuit terminal 6 and ground.
• If greater than the specified value, test the ground circuit for an open/high resistance.
4. Ignition ON, test for greater than 11 V between the 12 V reference circuit terminal 5 and ground.
• If less than the specified range, test the 12 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K17 Electronic Brake Control Module (EBCM).
5. If all circuits test normal, replace the B99 Steering Wheel Angle Sensor and verify the DTC does not reset.
• If the DTC resets, replace the K17 Electronic Brake Control Module (EBCM).
Repair Instructions
* Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Steering Angle Sensor Replacement (Removal and Replacement)
* Control Module References (Programming and Relearning) for EBCM replacement, programming and setup