P0102
DTC P0102 or P0103
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0102 00
- Mass Air Flow (MAF) Sensor Circuit Low Voltage
DTC P0103 00
- Mass Air Flow (MAF) Sensor Circuit High Frequency
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the amount of air entering the engine. The engine control module (ECM) uses the MAF sensor signal to provide the correct fuel delivery for all engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle condition. A large quantity of air entering the engine indicates an acceleration or high load condition.
The ECM applies 5 V to the MAF sensor on the MAF sensor signal circuit. The sensor uses the voltage to produce a frequency based on the inlet air flow through the sensor bore.
Conditions for Running the DTC
* The engine is running for greater than 1 s.
* The engine speed is greater than 300 RPM.
* The ignition voltage is greater than 10 V.
* The DTCs run continuously when the above conditions are met for greater than 1 s.
Conditions for Setting the DTC
P0102 00
The ECM detects that the MAF sensor signal is less than 900 Hz (0 g/s) for greater than 5 s.
P0103 00
The ECM detects that the MAF sensor signal is greater than 11 000 Hz (179 g/s) for greater than 5 s.
Action Taken When the DTC Sets
DTCs P0102 00 and P0103 00 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0102 00 and P0103 00 are Type B DTCs.
Diagnostic Aids
* Inspect the harness of the MAF sensor to verify that it is not routed too close to the following components:
- The ignition coils
- Any solenoids
- Any relays
- Any motors
* Inspect for any contamination, water intrusion, or debris on the sensing elements of the MAF sensor. If debris is present, clean the sensor. If the sensor cannot be cleaned, replace the sensor.
* A high resistance may cause a driveability concern before this DTC sets.
* A MAF sensor that is installed incorrectly may set this DTC.
Reference Information
Schematic Reference
Engine Controls Schematics ([1][2]Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Powertrain Diagnostic Trouble Code (DTC) Type Definitions)
Scan Tool Reference
Control Module References (Programming and Relearning)for scan tool information
Special Tools
EL 38522 - Variable Signal Generator
For equivalent regional tools, refer to Special Tools (Tools and Equipment).
Circuit/System Verification
1. Engine idling, observe the DTC information with a scan tool. DTC P0102 00 or P0103 00 should not set.
2. Verify the scan tool MAF sensor parameter is between 1.7-3.7 g/s.
3. Operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the B75B Mass Air Flow/Intake Air Temperature Sensor.
2. Ignition OFF, test for less than 5 ohm between the ground circuit terminal 2 and ground.
• If greater than the specified range, repair the ground circuit for an open/high resistance.
3. Ignition ON, test for B+ between the ignition voltage circuit terminal 4 and ground.
• If less than the specified range, test the ignition voltage circuit for a short to ground or an open/high resistance.
4. Test for 4.8-5.2 V between the signal circuit terminal 5 and ground.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.
5. Ignition OFF, connect the red lead of the EL 38522 - Variable Signal Generator to the signal circuit terminal 5 at the MAF/IAT sensor harness connector. Connect the battery voltage supply to B+, and ground the black lead.
6. Set the EL 38522 - Variable Signal Generator to the following specifications:
* Signal switch to 5 V
* Frequency switch to 5 KHz
Note: The engine will run rough and may stall.
* Duty Cycle switch to normal
7. Engine idling, observe the scan tool MAF Sensor Hz parameter. The scan tool MAF Sensor parameter should be between 4 950-5 025 Hz.
• If not within the specified range, replace the K20 Engine Control Module.
8. If the circuits test normal, replace the B75B Mass Air Flow/Intake Air Temperature Sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
Control Module References (Programming and Relearning)for ECM replacement, setup, and programming