Operation CHARM: Car repair manuals for everyone.
Home >> Chevrolet >> 2011 >> Impala V6-3.9L >> Repair and Diagnosis >> Heating and Air Conditioning >> Testing and Inspection >> Symptom Related Diagnostic Procedures >> HVAC - Manual >> Air Conditioning Compressor Malfunction

Air Conditioning Compressor Malfunction




Air Conditioning Compressor Malfunction

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.

Diagnostic Fault Information





Circuit/System Description

When the A/C switch is pressed, the HVAC control module grounds the A/C request signal circuit. This input will request the ECM to ground the A/C compressor clutch relay control circuit, which will switch the A/C CMPRSR relay. With the relay contacts closed, battery voltage is supplied to the A/C compressor clutch assembly.

Diagnostic Aids

The following conditions must be met in order for the ECM to turn on the compressor clutch:

* Battery voltage is between 9-18 volts.
* Engine coolant temperature (ECT) is less than 123°C (253°F).
* Engine speed is less than 4760 RPM.
* Engine speed is more than 600 RPM.
* A/C high side pressure is between 2929-269 kPa (425-39 psi).
* Throttle position is less than 100 percent.
* Evaporator temperature is greater than 0°C (32°F)
* ECM does not detect excessive torque load
* ECM does not detect insufficient idle quality.

Reference Information
Schematic Reference

HVAC Schematics (Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector End Views By Name)
Electrical Information Reference

* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the A/C CMPRSR relay.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal and ground.

• If the test lamp illuminates, test the control circuit for a short to voltage.

3. Verify that a test lamp illuminates between the ignition circuit terminal and ground.

• If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, test or replace the A/C CMPRSR relay.

4. Verify that a test lamp illuminates between the B+ circuit terminal and ground.

• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the control circuit terminal for a short to ground.

5. Disconnect the harness connector at the A/C compressor clutch.
6. Test for less than 1.0 ohm of resistance between the A/C compressor clutch ground circuit terminal A and ground.

• If greater than the specified range, test the ground circuit for an open/high resistance.

7. Connect the harness connector at the A/C compressor clutch.
8. Connect a 10A fused jumper wire between the B+ circuit terminal and the control circuit terminal. Verify the A/C compressor clutch is activated.

• If the A/C compressor clutch does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the A/C compressor clutch.

9. Connect a test lamp between the ignition circuit terminal and the control circuit terminal.
10. Command the A/C relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

11. If all circuits test normal, test or replace the A/C CMPRSR relay.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Air Conditioning Clutch Assembly Replacement (Service and Repair)
* Air Conditioning Compressor Replacement (LZE, LGD) (Removal and Replacement)
* Control Module References (Programming and Relearning) for HVAC control module and ECM replacement, setup and programming

pro multis · About Operation CHARM