P2537
DTC P2537
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC P2537
-
Ignition Accessory Switch Circuit Low Voltage
Diagnostic Fault Information
Circuit/System Description
The transmission control module (TCM) continuously monitors the voltage on the Ignition Accessory/Run circuit from the body control module (BCM). When the ignition switch is in the Accessory or Run position, the BCM sends a 12 volt wake up signal to the TCM. This wake up signal allows the TCM to power up and start functioning before the engine is started.
Conditions for Running the DTC
The ignition switch is in the Accessory or Run position.
Conditions for Setting the DTC
The TCM detects the Ignition Accessory/Run circuit is less than 6 volts for 1 minute.
Action Taken When the DTC Sets
DTC P2537 is a Type C DTC.
Conditions for Clearing the DTC
DTC P2537 is a Type C DTC.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics Electrical Diagrams
Connector End View Reference
* Component Connector End Views Fuel Pump and Level Sensor Assembly - Primary
* Inline Harness Connector End Views X102
Description and Operation
* Transmission General Description Transmission General Description
* Transmission Component and System Description Transmission Component and System Description
* Electronic Component Description Electronic Component Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Special Tools
DT-47825-10 - Jumper Harness
For equivalent regional tools, refer to Special Tools Tools and Equipment.
Circuit/System Verification
Note:
If other DTCs are set diagnose them first.
1. Ignition ON, clear the BCM and TCM of all DTCs.
2. Ignition OFF for 2 minutes.
3. Engine Running in park position for 1 minute. Verify DTC P2537 is not set in the TCM.
• If DTC P2537 is set
Refer to Circuit/System Testing below.
• If DTC P2537 is not set
4. After performing the above steps, verify that the DTC does not reset by operating the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions you observe from the Freeze Frame/Failure Records data. If the vehicle passes the Circuit/System Verification procedure, then STOP. Do not perform the Circuit/System Testing or Component Testing as this may result in an unnecessary part replacement. Refer to Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections.
Circuit/System Testing
1. Ignition OFF, disconnect the X1 16 way harness connector at the transmission. Install the DT-47825-10 - jumper harness to the X1 vehicle wire harness connector.
2. Ignition ON, verify a test lamp illuminates between X1 terminal 9 and ground at the transmission case.
• If the test lamp does not illuminate
1. Ignition OFF.
2. Disconnect the K9 body control module (BCM) connector X4.
3. Test the ignition voltage circuit for a short to ground or an open/high resistance between X4 terminal 22 of the K9 BCM and X1 terminal 9 of the Q8 control solenoid valve assembly.
• If the circuit test normal
Refer to Power Mode Mismatch Power Mode Mismatch.
• If the test lamp illuminates
3. Replace the Q8 control solenoid valve assembly.
Repair Instructions
* Perform the Reset Transmission Adapts Reset Procedure following all transmission related repairs.
* Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Refer to Control Module References Control Module References for control solenoid valve assembly replacement, programming, and setup.