B2575
DTC B2575 or B2699
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B2575 01
- Headlamps Control Circuit Short to Battery
DTC B2575 02
- Headlamps Control Circuit Short to Ground
DTC B2575 04
- Headlamps Control Circuit Open
DTC B2699 01
- Right Headlamp Control Circuit Short to Battery
DTC B2699 02
- Right Headlamp Control Circuit Short to Ground
DTC B2699 04
- Right Headlamp Control Circuit Open
Diagnostic Fault Information
Circuit/System Description
With the headlamp switch in the ON position, the headlamp switch headlamp ON signal circuit is grounded through the headlamp switch. The body control module (BCM) responds by applying battery positive voltage to the left and right low beam headlamp control circuits illuminating the low beam headlamps.
Conditions for Running the DTC
* Battery voltage must be between 9-16 V.
* Low beam headlamps ON.
Conditions for Setting the DTC
DTC B2575 01 and B2575 04
* The BCM detects an open/high resistance in the left low beam headlamp control circuit.
* The BCM detects a short to ground or an open/high resistance in the F8DA fuse B+ circuit.
DTC B2575 02
The BCM detects a short to ground in the left low beam headlamp control circuit.
DTC B2699 01 and B2699 04
* The BCM detects an open/high resistance in the right low beam headlamp control circuit.
* The BCM detects a short to ground or an open/high resistance in the F9DA fuse B+ circuit.
DTC B2699 02
The BCM detects a short to ground in the right low beam headlamp control circuit.
Actions Taken When the DTC Sets
* When DTC B2575 sets, the left low beam headlamp will be inoperative.
* When DTC B2699 sets, the right low beam headlamp will be inoperative.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views Sunshade - Left (D6I)
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
DTC B2575
1. Ignition OFF, disconnect the X1 harness connector at the K9 BCM.
2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 3 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the X1 harness connector at the K9 BCM.
4. Disconnect the harness connector at the E13L headlamp - left.
5. Ignition OFF, exterior lamps OFF, test for less than 5 ohm between the ground circuit terminal 2 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
6. Connect a test lamp between the control circuit terminal 1 and ground.
7. Ignition ON, command the Left Low Beam/Daytime Running Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
8. If all circuits test normal, replace the E13L headlamp bulb - left.
DTC B2699
1. Ignition OFF, disconnect the X1 harness connector at the K9 BCM.
2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the X1 harness connector at the K9 BCM.
4. Disconnect the harness connector at the E13R headlamp - right.
5. Ignition OFF, exterior lamps OFF, test for less than 5 ohm between the ground circuit terminal 2 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
6. Connect a test lamp between the control circuit terminal 1 and ground.
7. Ignition ON, command the Right Low Beam/Daytime Running Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
8. If all circuits test normal, replace the E13R headlamp bulb - right.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Headlamp Bulb Replacement Service and Repair
* Control Module References Control Module References for BCM replacement, setup, and programming