Front Fog Lamps Malfunction
Front Fog Lamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The fog lamp relay is supplied with battery voltage at all times. The fog lamp switch signal circuit is grounded momentarily by pressing the fog lamp switch. The body control module (BCM) energizes the fog lamp relay by applying ground to the fog lamp relay control circuit. When the fog lamp relay is energized, the relay switch contacts close and battery voltage is applied through the FOG LAMPS fuse to the fog lamp supply voltage circuit which illuminates the fog lamps.
Reference Information
Schematic Reference
Fog Lights Schematics Fog Lights Schematics
Connector End View Reference
Component Connector End Views A/C Compressor Clutch
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool Front Fog Lamp Switch parameter while activating the fog lamp switch. The parameter should change between Active and Inactive.
• If the parameter does not change between the commanded states, refer to Fog Lamp Switch Malfunction.
2. Turn the fog lamps ON and OFF with the fog lamps switch. The fog lamps should turn ON and OFF as selected.
• If the fog lamps do not change between the selected states, refer to Fog Lamp Malfunction.
3. Command the Display Test ON and OFF with a scan tool. The fog lamps indicator should turn ON and OFF when changing between the commanded states.
• It the fog lamps indicator illuminates during the test, replace the BCM.
• If the fog lamps indicator odes not illuminate during the test or remains illuminated at all times, replace the instrument cluster.
Circuit/System Testing
Fog Lamp Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the headlamp switch.
2. Ignition OFF, verify that a test lamp illuminates between B+ and the ground circuit terminal 8.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Front Fog Lamp Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 6 for a short to ground. If the circuit tests normal, replace the BCM.
4. Install a 3 A fused jumper wire between the signal circuit terminal 6 and the ground circuit terminal 8. Verify the scan tool Front Fog Lamp Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or and open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the headlamp switch.
Fog Lamps Malfunction
1. Ignition OFF, disconnect the X2 harness connector at the underhood fuse block.
2. Connect a test lamp between B+ and the control circuit terminal H5.
3. Command the Fog Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
4. Ignition OFF, connect the X2 harness connector at the underhood fuse block.
5. Disconnect the harness connector at the appropriate fog lamp.
6. Ignition OFF, test for less than 5 ohms between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect a test lamp between the control circuit terminal A and ground.
8. Command the Fog Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the underhood fuse block.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the underhood fuse block.
9. If all circuits test normal, test or replace the fog lamp.
Fog Lamp Indicator Malfunction
Ignition ON, with a scan tool perform the Display Test for the instrument panel cluster (IPC) and observe the front fog lamp indicator.
If the front fog lamp indicator illuminates during the test, replace the BCM.
If the front fog lamp indicator does not illuminate during the test or remains illuminated at all times, replace the IPC.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Accessory Wiring Junction Block Replacement Accessory Wiring Junction Block Replacement
* Headlamp Switch Replacement (Impala) Service and Repair
* Front Fog Lamp Bulb Replacement Service and Repair
* Front Fog Lamp Replacement Removal and Replacement
* Control Module References Control Module References for BCM or IPC replacement, setup, and programming