B297C
DTC B297B or B297C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B297B 5A
-
Driver Door Open Switch Circuit Not Plausible
DTC B297C 5A
-
Passenger Door Open Switch Circuit Not Plausible
Diagnostic Fault Information
Circuit/System Description
The keyless entry control module receives a discrete input from the driver and passenger door open switch signal circuits. The driver window motor receives a discrete input from the driver door ajar switch signal circuit. The passenger window switch receives a discrete input from the passenger door ajar switch signal circuit. The door open switches and the door ajar switches are integral to each door latch assembly.
The door open switch and the door ajar switch contacts will be open with the door is fully closed, the door switches within the door latch are designed so that the when the door is ajar, the contact in the door ajar switch closes and the window motor will then send a serial data message to the BCM indicating that the door is ajar. When the door is opened further, the contact in the door open switch will then close providing a ground for the door open signal circuit, the keyless entry control module will then detect that the door is open.
Conditions for Running the DTC
Battery voltage is between 9-16 V.
Conditions for Setting the DTC
B297B 5A
* The keyless entry control module detects the driver door open switch is Active while receiving a serial data message from the BCM that the driver door ajar switch is Inactive.
* The condition must be present for greater than 2 seconds
B297C 5A
* The keyless entry control module detects the passenger door open switch is Active while receiving a serial data message from the BCM that the passenger door ajar switch is Inactive.
* The condition must be present for greater than 2 seconds.
Action Taken When the DTC Sets
B297B 5A
The keyless entry control module ignores the inputs from the driver exterior door handle switch.
B297C 5A
The keyless entry control module ignores the inputs from the passenger exterior door handle switch.
Conditions for Clearing the DTC
* The DTC will be current for as long as the fault is present.
* When the keyless entry control module receives a serial data message from the BCM that the door is ajar before the keyless entry control module detects the door open switch is active, then the DTC will be a history DTC.
* A history DTC will clear after 50 ignition cycles.
Reference Information
Schematic Reference
Door Lock/Indicator Schematics Door Lock/Indicator Schematics
Connector End View Reference
Component Connector End Views Sunshade - Left (DH6)
Description and Operation
Power Door Locks Description and Operation Description and Operation
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool BCM Driver Door Ajar Switch parameter while opening and closing the driver door. The parameter should change between Active and Inactive.
• If the value does not change, refer to Driver Door Ajar Switch Malfunction.
2. Observe the scan tool keyless entry control module Driver Door Open Switch parameter while opening and closing the driver door. The parameter should change between Active and Inactive.
• If the value does not change, refer to Driver Door Open Switch Malfunction.
3. Observe the scan tool BCM Passenger Door Ajar Switch parameter while opening and closing the passenger door. The parameter should change between Active and Inactive.
• If the value does not change, refer to Passenger Door Ajar Switch Malfunction
4. Observe the scan tool keyless entry control module Passenger Door Open Switch parameter while opening and closing the passenger door. The parameter should change between Active and Inactive.
• If the value does not change, refer to Passenger Door Open Switch Malfunction.
Circuit/System Testing
Driver Door Ajar Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the A23D door latch assembly - driver.
2. Test for less than 10 ohms between the ground circuit terminal 8 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool BCM Driver Door Ajar Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 6 for a short to ground. If the circuit tests normal, replace the M74D window motor - driver.
4. Install a 3 A fused jumper wire between the signal circuit terminal 6 and ground. Verify the scan tool BCM Driver Door Ajar Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the M74D window motor - driver.
5. If all circuits test normal, test or replace the A23D door latch assembly - driver.
Driver Door Open Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the A23D door latch assembly - driver.
2. Ignition ON, verify the scan tool keyless entry control module Driver Door Open Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 7 for a short to ground. If the circuit tests normal, replace the K84 keyless entry control module.
3. Install a 3 A fused jumper wire between the signal circuit terminal 7 and ground. Verify the scan tool keyless entry control module Driver Door Open Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
4. If all circuits test normal, test or replace the A23D door latch assembly - driver
Passenger Door Ajar Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the A23P door latch assembly - passenger.
2. Test for less than 10 ohms between the ground circuit terminal 3 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool BCM Passenger Door Ajar Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 1 for a short to ground. If the circuit tests normal, replace the M74P window motor - passenger.
4. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground. Verify the scan tool BCM Passenger Door Ajar Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the M74P window motor - passenger.
5. If all circuits test normal, test or replace the A23P door latch assembly - passenger.
Passenger Door Open Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the A23P door latch assembly - passenger.
2. Ignition ON, verify the scan tool keyless entry control module Passenger Door Open Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit tests normal, replace the K84 keyless entry control module.
3. Install a 3 A fused jumper wire between the signal circuit terminal 2 and ground. Verify the scan tool keyless entry control module Passenger Door Open Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
4. If all circuits test normal, test or replace the A23P door latch assembly - passenger
Component Testing
1. Ignition OFF, disconnect the harness connector at the appropriate A23 door latch assembly.
2. With the switch in the open position, test for infinite resistance between the signal terminal and ground terminal listed below:
* A23D door latch assembly - driver signal terminal 6 and ground terminal 8
* A23P door latch assembly - passenger signal terminal 1 and ground terminal 3
• If not the specified value, replace the door latch assembly
3. With the switch in the closed position, test for less than 5 ohms between the signal terminal and ground terminal listed below:
* A23D door latch assembly - driver signal terminal 6 and ground terminal 8
* A23P door latch assembly - passenger signal terminal 1 and ground terminal 3
• If greater than the specified range, replace the A23 door latch assembly
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Front Side Door Lock Replacement Front Side Door Lock Replacement
* Control Module References Control Module References for BCM and keyless entry control module replacement, setup and programming