Operation CHARM: Car repair manuals for everyone.
Home >> Chevrolet >> 2012 >> Malibu V6-3.6L >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> B Code Charts >> B0183 >> CJ2

CJ2




DTC B0163, B0183, or B1405 (CJ2)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0163 02

-
Passenger Compartment Temperature Sensor Circuit Short to Ground

DTC B0163 05

-
Passenger Compartment Temperature Sensor Circuit High Voltage/Open

DTC B0183 02

-
Solar Load Sensor Circuit Short to Ground

DTC B0183 05

-
Solar Load Sensor Circuit High Voltage/Open

DTC B1405 02

-
Control Module Voltage Reference Output 2 Circuit Short to Ground

DTC B1405 05

-
Control Module Voltage Reference Output 2 Circuit High Voltage/Open

Diagnostic Fault Information






Circuit/System Description

The ambient light/sunload sensor integrates the sunload sensor and passenger compartment temperature sensor.

This sensor assembly provides information about:

* Sun heat intensity

* Elevation

* Azimuth

* Passenger compartment temperature

The sunload sensor is connected to ground and to a 12 V clocked power supply through the HVAC control module. This clocked power supply is to power the sensor electronics and to work as a clock generator to the sunload sensor micro controller. The sensor uses a pulse signal for data identification and transferring the sun intensity measurement. At each positive transition from the clocked supply input, the sunload sensor micro controller will shift channels enabling new intensity measurement on the signal output to the HVAC control module. The signal voltage varies between 0-4 V.

The passenger compartment temperature sensor is a negative temperature co-efficient thermistor. A signal and low reference circuit enables the sensor to operate. As the air temperature increases, the sensor resistance decreases. The sensor signal varies between 0-5 V.

Bright or high intensity light causes the vehicles interior temperature to increase. The HVAC system compensates for the increased temperature by diverting additional cool air into the vehicle.

Conditions for Running the DTC

* Ignition ON.

* The HVAC control module is ON.

Conditions for Setting the DTC

B0163 02 or B0163 05

The HVAC control module detects the sensor signal out of range. The signal voltage is less than 0.1 V or greater than 4.9 V for more than 50 ms.

B0183 02

The 5 V identification pulse is not received.

B0183 05

The input signal is static and greater than 4.8 V.

B1405 02

Clocked supply for multi zone sensor is shorted to ground.

B1405 05

Clocked supply for multi zone sensor is shorted to voltage or open.

Action Taken When the DTC Sets

* The system will use the last valid values as default.

* If no value is read at the time of fault, the HVAC Control Module uses 0 W/m2 as intensity, 45° for elevation and -75° for azimuth.

Conditions for Clearing the DTC

B0163 02 or B0163 05

The sensor signal is within specified range between 0.1-4.9 V.

B0183 02

The 5 V identification pulse will be received.

B0183 05

The correct pulse signal succession will be received.

B1405 02 or B1405 05

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

HVAC Schematics HVAC - Automatic

Connector End View Reference

Component Connector End Views Sunshade - Left (DH6)

Description and Operation

Automatic HVAC Description and Operation HVAC - Automatic

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

Scan Tool Reference

Control Module References Control Module References for scan tool information

Circuit/System Verification

1. Verify that DTC B1405 02 or B1405 05 is not set.

• If DTC B1405 is set

Refer to Ambient Light/Sunload Sensor Power Supply Malfunction.

• If DTC B1405 is not set

2. Verify that DTC B0163 02 or B0163 05 is not set.

• If DTC B0163 is set

Refer to Passenger Compartment Temperature Sensor Circuit Malfunction.

• If DTC B0163 is not set

3. Verify that DTC B0183 02 or B0183 05 is not set.

• If DTC B0183 is set

Refer to Sunload Sensor Circuit Malfunction.

• If DTC B0183 is not set

4. Measure actual inside air temperature using a thermometer. Compare this value to the scan tool Passenger Compartment Air Temperature parameter. The measured temperature should be within 5°C (9°F) difference of parameter value.

• If not within the specified range

Replace the B10B Ambient Light/Sunload Sensor.

• If within the specified range

5. All OK.

Circuit/System Testing

Ambient Light/Sunload Sensor Power Supply Malfunction

1. Ignition OFF, disconnect the harness connector at the B10B Ambient Light/Sunload Sensor.

2. Test for less than 5 ohms between the B10B Ambient Light/Sunload Sensor ground circuit terminal 6 and ground.

• If 5 ohms or greater

Repair the open/high resistance in the circuit.

• If less than 5 ohms

3. Disconnect the X1 harness connector at the K33 HVAC Control Module, ignition ON.

4. Test for less than 0.3 V between the reference voltage circuit terminal 2 and ground.

• If greater than 0.3 V

Repair the short to voltage on the circuit.

• If less than 0.3 V

5. Ignition OFF.

6. Test for infinite resistance between the reference voltage circuit terminal 2 and ground.

• If less than infinite resistance

Repair the short to ground on the circuit.

• If infinite resistance

7. Test for less than 5 ohms between the B10B Ambient Light/Sunload Sensor reference voltage circuit terminal 2 and control circuit terminal 20 X1 at the K33 HVAC Control Module harness connector.

• If 5 ohms or greater

Repair the open/high resistance in the circuit.

• If less than 5 ohms

8. Replace the B10B Ambient Light/Sunload Sensor and verify the DTC does not reset.

• If DTC resets

Replace the K33 HVAC Control Module.

• If DTC does not reset

9. All OK.

Passenger Compartment Temperature Sensor Circuit Malfunction

1. Ignition OFF, disconnect the harness connector at the B10B Ambient Light/Sunload Sensor, ignition ON.

2. Test for 4.8-5.2 V between the signal circuit terminal 3 and ground.

• If less than 4.8 V

1. Ignition OFF, disconnect the X1 harness connector at the K33 HVAC Control Module.

2. Test for infinite resistance between the signal circuit and ground.

• If less than infinite resistance, repair the short to ground on the circuit.

• If infinite resistance

3. Test for less than 2 ohms in the signal circuit end to end.

• If 2 ohms or greater, repair the open/high resistance in the circuit.

• If less than 2 ohms, replace the K33 HVAC Control Module.

• If greater than 5.2 V

1. Ignition OFF, disconnect the X1 harness connector at the K33 HVAC Control Module, ignition ON.

2. Test for less than 0.3 V between the signal circuit and ground.

• If greater than 0.3 V, repair the short to voltage on the circuit.

• If less than 0.3 V, replace the K33 HVAC Control Module.

• If within 4.8-5.2 V

3. Replace the B10B Ambient Light/Sunload Sensor and verify the DTC does not reset.

• If DTC resets

Replace the K33 HVAC Control Module.

• If DTC does not reset

4. All OK.

Sunload Sensor Circuit Malfunction

1. Ignition OFF, disconnect the harness connector at the B10B Ambient Light/Sunload Sensor and the X1 harness connector at the K33 HVAC Control Module, ignition ON.

2. Test for less than 0.3 V between the signal circuit terminal 4 and ground.

• If greater than 0.3 V

Repair the short to voltage on the circuit.

• If less than 0.3 V

3. Ignition OFF.

4. Test for infinite resistance between the signal circuit terminal 4 and ground.

• If less than infinite resistance

Repair the short to ground on the circuit.

• If infinite resistance

5. Test for less than 5 ohms between the B10B Ambient Light/Sunload Sensor signal circuit terminal 4 and control circuit terminal 13 X1 at the K33 HVAC Control Module harness connector.

• If 5 ohms or greater

Repair the open/high resistance in the circuit.

• If less than 5 ohms

6. Replace the B10B Ambient Light/Sunload Sensor and verify the DTC does not reset.

• If DTC resets

Replace the K33 HVAC Control Module.

• If DTC does not reset

7. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.

* Sun Load Temperature Sensor Replacement HVAC - Automatic

* Control Module References Control Module References for HVAC control module replacement, programming and setup

pro multis · About Operation CHARM