P0976
DTC P0976 or P0977
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0976
- Shift Solenoid (SS) 2 Control Circuit Low Voltage
DTC P0977
- Shift Solenoid (SS) 2 Control Circuit High Voltage
Diagnostic Fault Information
Circuit/System Description
The shift solenoid (SS) 2 is part of the control solenoid valve assembly which has no serviceable components. SS 2 is a normally closed (NC) ON/OFF solenoid and is controlled by the TCM through a low side driver. When the SS 2 is energized (ON), SS 2 fluid pressure is directed to the clutch select valve 3, which allows the valve to overcome the spring pressure and move to the applied position. Power to the SS 2 is supplied by the TCM through a high side driver (HSD). The HSD protects the circuit and components from excessive current flow. If excessive current flow is detected, the HSD will turn OFF. When the fault is corrected, the HSD will reset.
Conditions for Running the DTC
P0976
* The engine speed is greater than 400 RPM for 5 seconds.
* The ignition voltage is 8.6 volts or greater.
* DTC P0976 has not set this ignition cycle.
P0977
* The engine speed is greater than 400 RPM for 5 seconds.
* The ignition voltage is 8.6 volts or greater.
* DTC P0977 has not set this ignition cycle.
Conditions for Setting the DTC
P0976
The TCM detects a short to ground on the SS 2 control circuit for 2 seconds.
P0977
The TCM detects an open or short to power on the SS 2 control circuit for 2 seconds.
Action Taken When the DTC Sets
P0976
* DTC P0976 is a Type B DTC.
* The TCM freezes transmission adaptive functions.
* The TCM commands maximum line pressure.
P0977
* DTC P0977 is a Type A DTC.
* The TCM limits the transmission to reverse and 5th gear.
* The TCM inhibits the torque converter clutch (TCC).
* The TCM commands maximum line pressure.
* The TCM freezes transmission adaptive functions.
* The TCM turns the high side driver OFF.
* The TCM inhibits Tap Up/Down function.
* The TCM inhibits manual shifting of forward gears.
Conditions for Clearing the DIC/DTC
* DTC P0976 is a Type B DTC.
* DTC P0977 is a Type A DTC.
Reference Information
Connector End View Reference
* Component Connector End Views Connector End Views By Name
* Inline Harness Connector End Views Connector Views
Description and Operation
Transmission General Description Transmission General Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Special Tools
DT-47825-20 Adapter Harness
Circuit/System Verification
1. Operate the vehicle in 3rd gear long enough to ensure at least a 3°C (5°F) rise in TCM temperature.
2. Place the gear selector in Reverse for 5 seconds and then idle the vehicle in Park for 5 seconds. Verify with a scan tool the following test status parameters display OK:
* Shift Sol. 2 Ctrl. Ckt. High Voltage Test Status
* Shift Sol. 2 Ctrl. Ckt. Open Test Status
* Shift Sol. 2 Ctrl. Ckt. Low Voltage Test Status
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly Replacement Service and Repair.
2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection Component Tests and General Diagnostics.
3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.
4. Connect DT-47825-20 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly electrical connector.
5. Ignition ON, verify with a scan tool the following test status parameters display OK:
* Shift Sol. 2 Ctrl. Ckt. High Voltage Test Status
* Shift Sol. 2 Ctrl. Ckt. Open Test Status
* Shift Sol. 2 Ctrl. Ckt. Low Voltage Test Status
• If any test status parameter displays Fault or Malfunction, replace the control solenoid valve assembly.
Repair Instructions
Note:
* Perform the Reset Transmission Adapts Programming and Relearning following all transmission related repairs.
* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection Component Tests and General Diagnostics.
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
Control Module References Control Module References for control solenoid valve assembly replacement, setup, and programming