Operation CHARM: Car repair manuals for everyone.

Engine Replacement




Engine Replacement

Special Tools

EN-48244 - Engine Assembly Remove/Install Pallet Supporter

Removal Procedure

1. Remove the battery and battery tray. Refer to Battery Tray Replacement Service and Repair.

2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Service and Repair.

3. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging Refrigerant Recovery and Recharging.

4. Remove the front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation Service and Repair.

5. Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .

6. Drain the cooling system. Refer to Cooling System Draining and Filling Cooling System Draining and Filling.




7. Remove the lower intermediate steering shaft bolt (1) and slide the shaft away from steering column. Refer to Intermediate Steering Shaft Replacement Intermediate Steering Shaft Replacement.




8. Remove the air cleaner assembly (1). Refer to Air Cleaner Assembly Replacement Service and Repair.




9. Remove the junction block cover (1).




10. Remove the positive battery cable nut (1) from the junction block.

11. Remove the positive battery cable (2) from the junction block.




12. Remove the positive cable nut (1) and battery positive cable, from the battery positive cable junction block.

13. Disconnect the body wiring master harness connector (2), from the battery positive cable junction block.




14. Remove the junction block nut (1).

15. Remove the junction block bolts (2).

16. Disconnect the wiring harness from the junction block base.

17. Remove the junction block (3) from the base.

18. Disconnect the wiring harness plug from the front compartment fuse block.




19. Reposition the wiring harness (1) on top of the engine.




20. Remove the ground nuts (1) and reposition the wiring harness (2) aside.




21. Disconnect the electrical connector and remove the brake booster hose (1).




22. Disconnect the heater inlet hose (1) from the heater core. Refer to Heater Inlet Hose Replacement (LDE, LUW) Heater Inlet Hose Replacement (LDE, LUW)Heater Inlet Hose Replacement (LUV) .




23. Disconnect the heater outlet hose (1) from the heater core. Refer to Heater Outlet Hose Replacement (LUV) Heater Outlet Hose Replacement (LDE, LUW) Heater Outlet Hose Replacement (LDE, LUW).




24. If equipped with an automatic transmission, disconnect the transmission range selector lever cable terminal (1) from the transmission manual shift lever pin.

25. Remove the transmission range selector lever cable (2) from the cable bracket.




26. If equipped with manual transmission, disconnect the shift lever and selector lever cable end (1) from the transmission shift lever and selector lever.

27. Pull the cable retainers (2) to release the shift lever and selector lever cable from the shift lever and selector lever cable bracket.

28. Disconnect the shift lever and selector lever cable from the shift lever and selector lever cable bracket.




29. Remove the radiator surge tank (2) and position aside. Refer to Radiator Surge Tank Replacement Radiator Surge Tank Replacement.

30. Disconnect the fan connector.




31. Remove air conditioning compressor and condenser hose nut (1).

32. Remove air conditioning compressor and condenser hose (2) from refrigerant hose.




33. Disconnect the fuel feed pipe (1). Refer to Plastic Collar Quick Connect Fitting Service Procedures.




34. Disconnect the evaporative emission pipe (1). Refer to Plastic Collar Quick Connect Fitting Service Procedures.




35. Remove the wheel drive shafts. Refer to Front Wheel Drive Shaft Replacement Front Wheel Drive Shaft Replacement

36. Remove the front exhaust pipe. Refer to Exhaust Front Pipe Replacement (LUV,LUW) Service and Repair.




37. If equipped with an automatic transmission, remove the lower transmission nut (1) and the lower transmission bolts (2, 3, 4).




38. If equipped with manual transmission, remove the lower transmission bolt (3) and nut (4).

39. Remove the lower transmission bolts (1, 2).




40. Remove the frame front bolts (1).

41. Position the EN-48244 - engine assembly remove/install pallet supporter under the powertrain and support with blocks of wood.




42. Remove the upper frame suspension retaining bolts (1) on both sides.




43. Remove the right side engine mount (4). Refer to Engine Mount Replacement - Right Side .




44. Remove and DISCARD the transmission mount bolts (1) - left side. Refer to Transmission Mount Replacement - Left Side Transmission Mount Replacement - Left Side.

45. Disconnect any additional electrical connections as necessary.

46. Raise the vehicle until the powertrain is clear for removal.




47. If equipped with an automatic transmission, remove the starter. Refer to Starter Replacement (LUW) Service and RepairStarter Replacement (LUV) .

48. Mark the relationship of the flex plate to the torque converter for reassembly.

49. Remove and DISCARD the flex plate to torque converter bolts (1).




50. If equipped with an automatic transmission, remove the upper transmission to engine bolts (1) and separate the engine and transmission.




51. If equipped with manual transmission, remove the upper transmission to engine bolts (1). And separate the engine and transmission.

52. Disconnect any electrical connectors as needed.

53. Transfer parts as necessary.

Installation Procedure

1. Install the transmission to the engine.





Caution: Refer to Fastener Caution Fastener Caution.

2. If equipped with a manual transmission, install the upper transmission to engine bolts (1) to 60 N•m (44 lb ft).




3. If equipped with automatic transmission, install the upper transmission to engine bolts (1) and tighten to 60 N•m (44 lb ft).




4. If equipped with an automatic transmission, install the torque converter to flex plate bolts (1) and tighten to 60 Nm (44 lb ft).

5. Install the starter. Refer to Starter Replacement (LUW) Service and RepairStarter Replacement (LUV) .

6. Position the powertrain under the vehicle and slowly lower the body onto the powertrain.





Caution: Refer to Torque-to-Yield Fastener Caution Torque-to-Yield Fastener Caution.

7. Install the NEW left transmission mount to transmission bolts (1) and tighten to 50 Nm (37 lb ft) plus 70 degrees.




8. Install the right side engine mount (4). Refer to Engine Mount Replacement - Right Side .

9. Connect all previously disconnected electrical connections.




10. Install the frame (3) rear bolts (2) and front bolts (1), tighten a little bit.




11. Install the frame (3) rear bolts (2) and tighten to 135 Nm (100 lb ft).

12. Install the frame (3) front bolts (1) and tighten to 58 Nm (43 lb ft).




13. Install the upper frame suspension retaining bolts (1) on both sides and tighten to 135 Nm (100 lb ft).

14. Remove the lift table.




15. If equipped with manual transmission, install the lower transmission bolts (1) and tighten to 60 Nm (44 lb ft).

16. Install the lower transmission bolts (2) and tighten 40 Nm (30 lb ft).

17. Install the lower transmission bolt (3) and nut (4) and tighten to 40 Nm (30 lb ft).




18. If equipped with an automatic transmission, install the lower transmission bolts (2, 4) and tighten to 60 Nm (44 lb ft).

19. Install the lower transmission bolts (3) and the lower transmission nut (1) and tighten to 40 Nm (30 lb ft).

20. Install the front exhaust pipe. Refer to Exhaust Front Pipe Replacement (LUV,LUW) Service and Repair.




21. Install the wheel drive shafts. Refer to Front Wheel Drive Shaft Replacement Front Wheel Drive Shaft Replacement




22. Connect the evaporative emission pipe (1). Refer to Plastic Collar Quick Connect Fitting Service Procedures.




23. Connect the fuel feed pipe (1). Refer to Plastic Collar Quick Connect Fitting Service Procedures.




24. Install air conditioning compressor and condenser hose to the refrigerant hose.

25. Install air conditioning compressor and condenser hose nut (1) tighten nut to 22 N•m (16 lb ft).




26. Install the radiator surge tank (2). Refer to Radiator Surge Tank Replacement Radiator Surge Tank Replacement.

27. Connect the fan connector.




28. If equipped with manual transmission, Connect the shift lever and selector lever cable end (1) to the transmission shift lever and selector lever.

29. Connect the shift lever and selector lever cable to the shift lever and selector lever cable bracket.

30. Install the cable retainers (2) to the shift lever and selector lever cable bracket.




31. If equipped with automatic transmission, install the transmission range selector lever cable (2) to the cable bracket.

32. Connect the transmission range selector lever cable terminal (1) to the transmission manual shift lever pin.

33. Adjust the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Adjustment Adjustments.




34. Connect the heater inlet hose (2) from the heater core. Refer to Heater Inlet Hose Replacement (LDE, LUW) Heater Inlet Hose Replacement (LDE, LUW)Heater Inlet Hose Replacement (LUV) .




35. Connect the heater outlet hose (2) from the heater core. Refer to Heater Outlet Hose Replacement (LUV) Heater Outlet Hose Replacement (LDE, LUW) Heater Outlet Hose Replacement (LDE, LUW).




36. Connect the electrical connector and install the brake booster hose (1).




37. Install the ground nuts (1) and wiring harness (2).




38. Clip in the wiring harness plugs (1).




39. Install the junction block to the base (3).

40. Install the junction block bolts (2) and tighten to 5 N•m (44 lb in).

41. Install the junction block nut (1) and tighten to 5 N•m (44 lb in).




42. Install the battery positive cable to the battery positive cable junction block and tighten nut (1) to 5 N•m (44 lb in).

43. Connect the body wiring master harness connector (2), to the battery positive cable junction block.




44. Position the positive battery cable (2) to the junction block.

45. Install the positive battery cable nut (1) and tighten to 7 N•m (62 lb in).




46. Install the junction block cover (1).




47. Install the air cleaner assembly (1). Refer to Air Cleaner Assembly Replacement Service and Repair.




48. Install the lower intermediate steering shaft bolt (1). Refer to Intermediate Steering Shaft Replacement Intermediate Steering Shaft Replacement.

49. Install the battery and battery tray. Refer Battery Tray Replacement Service and Repair.

50. Install the front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation Service and Repair.

51. Install the front bumper fascia. Refer to Front Bumper Fascia Replacement .

52. Evacuate and charge the refrigerant system. Refer to Refrigerant Recovery and Recharging Refrigerant Recovery and Recharging.

53. Fill the cooling system. Refer to Cooling System Draining and Filling Cooling System Draining and Filling.