Daytime Running Lamps Malfunction
Daytime Running Lamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The ambient light sensor is used to monitor outside lighting conditions. The body control module (BCM) provides a low reference ground and 5-volt reference signal to the ambient light sensor. Depending on outside lighting conditions, the ambient light sensor provides a voltage signal to the BCM that will vary between 0.2 and 4.9 volts. The BCM monitors the ambient light sensor signal circuit to determine if outside lighting conditions are correct for either daytime running lights (DRL) or automatic headlamp system control when the headlamp switch is in the AUTO position. In daylight conditions, the BCM will command the low beam headlamps (DRLs) ON by applying low voltage to the low beam headlamp control circuits illuminating the low beam headlamps at reduced intensity. Any function or condition that turns on the headlamps will cancel DRL operation.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Ignition ON.
2. Verify the low beam headlamps turn on & off when commanding the Low Beam Headlamps ON and OFF with a scan tool.
• If the low beam headlamps do not turn ON and OFF
Refer to Headlamps Malfunction Headlamps Malfunction.
• If the low beam headlamps turn ON and OFF
3. Ignition ON, park brake released.
4. Verify the scan tool BCM Park Brake Status parameter displays released.
• If the park brake status parameter does not display released
Refer to Brake Warning Indicator Malfunction Brake Warning Indicator Malfunction.
• If the parameter displays released
5. Refer to Circuit/System Testing.
Circuit/System Testing
1. Ignition OFF, scan tool disconnected, all doors closed, all accessories OFF, open and close drivers door, disconnect the harness connector at the B10 ambient light sensor. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 15 ohms between the ground circuit terminal 6 and ground.
• If 15 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 15 ohms
3. Ignition ON.
4. Verify the scan tool Ambient Light Sensor parameter is greater than 4.65 V.
• If 4.65 V or less
1. Ignition OFF, disconnect the X2 harness connector at the K9 body control module.
2. Test for infinite resistance between the signal circuit terminal 5 and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K9 body control module.
• If greater than 4.65 V
5. Install a 3 A fused jumper wire between the signal circuit terminal 5 and the ground circuit terminal 6.
6. Verify the scan tool Ambient Light Sensor parameter is less than 0.196 V.
• If 0.196 V or greater
1. Ignition OFF, disconnect the X2 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the signal circuit terminal 5 and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V
3. Test for less than 2 ohms in the signal circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If less than 0.196 V
7. Test or replace the B10 ambient light sensor.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Sun Load Temperature Sensor Replacement Service and Repair
* Control Module References Control Module References for BCM replacement, programming, and setup