B3810
DTC B3810
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC B3810 02
- Headlamp Washer Relay Circuit Short to Ground
Diagnostic Fault Information
Circuit/System Description
The body control module (BCM) controls the washer motor based on an input from the windshield wiper washer switch. The BCM monitors the washer switch through the windshield washer switch signal circuit. When the WASH switch is closed, ground is supplied to the front washer switch signal circuit. When this is seen, the BCM will command the front washer fluid pump and the low speed wipers on. When Headlamp Wash Equipped, the headlamps shall be sprayed with wash fluid as a result of an extended Windshield Wash Switch Activation. In order to preserve wash fluid, the feature shall only be allowed to activate if the Low or High Beam Headlamps are active. In addition, after the initial Headlamp Wash operation has been performed, additional headlamp washes shall not be performed for the next 4 Windshield Wash activations or for 48 hours whichever comes first. In the event that the system has detected a Stuck Front Wash Switch condition, the Headlamp Wash Feature shall be disabled.
Conditions for Running the DTC
* Ignition ON.
* The system voltage is between 9-16 V.
Conditions for Setting the DTC
A short to ground is detected in the headlamp washer relay control circuit.
Action Taken When the DTC Sets
Washer operation is suspended.
Conditions for Clearing the DTC
* A current DTC clears when the diagnostic runs and passes.
* A history DTC will clear after 50 consecutive ignition cycles without a fault present.
Diagnostic Aids
The headlamp wash feature shall only be allowed to be activated if the low or high beam headlamps are active too.
Reference Information
Schematic Reference
Wiper/Washer Schematics Electrical Diagrams
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Wiper/Washer System Description and Operation Description and Operation
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
1. Ignition OFF and all vehicle systems OFF, disconnect the KR2 headlamp washer fluid pump relay. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 10 ohms between the ground circuit terminal 86 and ground.
• If 10 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 10 ohms
3. Ignition ON.
4. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
• If the test lamp does not illuminate and the circuit fuse is OK
1. Ignition OFF.
2. Test for less than 2 ohms in the ignition circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, verify the fuse is OK and there is voltage at the fuse.
• If the test lamp does not illuminate and the circuit fuse is open
1. Ignition OFF, repair the short to ground on the circuit
2. Test for infinite resistance between the ignition circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the KR2 headlamp washer fluid pump relay.
• If the test lamp illuminates
5. Connect a test lamp between the control circuit terminal 85 and the ground circuit terminal 86.
6. Verify the test lamp turns ON and OFF when commanding the Headlamp Washer Relay Command ON and OFF with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the X5 harness connector at the K9 body control module.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If the test lamp is always ON
1. Ignition OFF, disconnect the X5 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the control circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K9 body control module.
• If the test lamp turns ON and OFF
7. Verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
• If the test lamp illuminates
Repair the short to voltage on the control circuit
• If the test lamp does not illuminate
8. Test or replace the KR2 headlamp washer fluid pump relay.
Component Testing
Relay Test
1. Ignition OFF, disconnect the KR2 headlamp washer fluid pump relay.
2. Test for 60-200 ohms between terminals 85 and 86.
• If less than 60 or greater than 200
Replace the KR2 headlamp washer fluid pump relay.
• If between 60-200 ohms
3. Test for infinite resistance between the terminals listed below:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If less than infinite resistance
Replace the KR2 headlamp washer fluid pump relay.
• If infinite resistance
4. Test for less than 10 ohms between terminals 30 and 87A.
• If 10 ohms or greater
Replace the KR2 headlamp washer fluid pump relay.
• If less than 10 ohms
5. Install a 10 A fused jumper wire between relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground.
6. Test for less than 10 ohms between terminals 30 and 87.
• If 10 ohms or greater
Replace the KR2 headlamp washer fluid pump relay.
• If less than 10 ohms
7. All OK.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Relay Replacement (Within an Electrical Center) Relay Replacement (Within an Electrical Center)Relay Replacement (Attached to Wire Harness) Relay Replacement (Attached to Wire Harness)
* Headlamp Washer Pump Replacement Service and Repair
* Windshield Wiper and Washer Switch Replacement Service and Repair
* Accessory Wiring Junction Block Replacement Removal and Replacement
* Control Module References Control Module References for BCM replacement, programming and setup