B3884
DTC B3884
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC B3884 02
- Center High Mounted Brake Lamp Circuit Short to Ground
Diagnostic Fault Information
Circuit/System Description
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5 V reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the right and left stop lamp control circuits, engine control module (ECM), and center high mounted stop lamp control circuit.
Conditions for Running the DTC
* Battery voltage must be between 9-16 V.
* Brakes APPLIED.
Conditions for Setting the DTC
The BCM detects a short to ground in the center high mounted stop lamp control circuit.
Actions Taken When the DTC Sets
The BCM will not illuminate the center high mounted stop lamp.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Exterior Lights Schematics Exterior Lights Schematics
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
1. Ignition OFF, exterior lamps OFF, trunk latch latched, disconnect the harness connector at the E6 center high mounted stop lamp.
2. Test for less than 5 ohms between the appropriate ground circuit terminal listed below and ground.
* Terminal 2 - coupe
* Terminal B - convertible
• If 5 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 5 ohms
3. Connect a test lamp between the appropriate control circuit terminal listed below and ground, ignition ON.
* Terminal 1 - coupe
* Terminal A - convertible
4. Verify the test lamp turns ON and OFF when commanding the Center Brake Lamp ON and OFF with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the X4 harness connector at the K9 body control module.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If the test lamp is always ON
1. Ignition OFF, disconnect the X4 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the control circuit terminal and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K9 body control module.
• If the test lamp turns ON and OFF
5. Test or replace the E6 center high mounted stop lamp.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* High Mount Stop Lamp Replacement (Coupe) High Mount Stop Lamp Replacement (Coupe)High Mount Stop Lamp Replacement (ZL1) High Mount Stop Lamp Replacement (ZL1)High Mount Stop Lamp Replacement (Convertible) High Mount Stop Lamp Replacement (Convertible)
* Control Module References Control Module References for BCM replacement, programming, and setup