P023F
DTC P0231, P0232, or P023F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0231
- Fuel Pump Control Circuit Low Voltage
DTC P0232
- Fuel Pump Control Circuit High Voltage
DTC P023F
- Fuel Pump Control Circuit
Diagnostic Fault Information
Circuit/System Description
The engine control module (ECM) supplies voltage to the fuel pump control module when the ECM detects that the ignition is on. The voltage from the ECM to the fuel pump control module remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the fuel pump control module supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel line pressure.
Conditions for Running the DTC
P0231, P023F
The ignition voltage is between 9-18 V.
P0232
The control enable voltage signal supplied for the ECM to fuel pump control module is inactive for 4 seconds after engine has been shut off.
Conditions for Setting the DTC
The fuel pump control module detects a fault on the fuel pump voltage circuit that is less than 11 V or greater than 18 V.
Action Taken When the DTC Sets
DTCs P0231, P0232, and P023F are Type A DTCs.
Conditions for Clearing the DTC
DTCs P0231, P0232, and P023F are Type A DTCs.
Diagnostic Aids
Using the Failure Records data may help locate an intermittent condition. If you cannot duplicate the DTC, the information in the Failure Records can help determine how many miles since the DTC set. The Fail Counter and Pass Counter can help determine how many ignition cycles that the diagnostic test reported a pass and/or a fail.
On vehicles equipped with a high pressure mechanical pump on Direct Fuel Injection engines, the vehicle may continue to run even though the pump in the fuel tank is not operating.
Reference Information
Schematic Reference
Engine Controls Schematics ((LFX)) [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Fuel System Description Fuel System Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the G12 fuel pump. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 10 ohms between the low reference circuit terminal 2 and ground.
• If 10 ohms or greater
1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module.
2. Test for less than 2 ohms in the low reference circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K27 fuel pump control module.
• If less than 10 ohms
3. Connect a test lamp between the control circuit terminal 1 and the low reference circuit terminal 2.
4. Ignition ON.
5. Verify the test lamp turns ON and OFF when commanding the fuel pump ON and OFF with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K27 fuel pump control module.
• If the test lamp is always ON
1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module, ignition ON.
2. Test for less than 1 V between the control circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K27 fuel pump control module.
• If the test lamp turns ON and OFF
6. Replace the G12 fuel pump.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Fuel Tank Fuel Pump Module Replacement - Right Side Fuel Tank Fuel Pump Module Replacement - Right Side
* Control Module References Control Module References for fuel pump control module replacement, programming and setup