P2714

DTC P2714 or P2715

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P2714
- Pressure Control (PC) Solenoid Valve 4 - Stuck Off

DTC P2715
- Pressure Control (PC) Solenoid Valve 4 - Stuck On

Circuit/System Description

The clutch pressure control (PC) solenoid 4 is part of the control solenoid valve assembly, which has no serviceable parts. The Clutch Pressure Control Solenoid 4 regulates transmission fluid pressure to the 2-6 clutch regulator valve which controls pressure to the 2-6 clutch. The Transmission Control Module calculates gear ratio based on the RPM signals from the input speed sensor (ISS) and the output speed sensor (OSS). The Transmission Control Module compares the expected transmission gear ratio to the calculated gear ratio for each commanded gear.

Conditions for Running the DTC

P2714

* TCM DTC P0716, P0717, P0722, P0723, or P182E is not set.

* ECM DTC P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, or P042E is not set.

* The accelerator pedal position is 0.5 percent or greater.

* The output speed is 16 RPM or greater.

* The ignition voltage is between 8.6-32 V.

* The engine speed is between 400-7500 RPM for 5 seconds.

* The transmission temperature is -6.6°C (20°F) or greater.

* The throttle position signal is valid.

* High side driver (HSD) is enabled.

* The PC solenoid 4 is commanded ON, applying the 2-6 clutch.

P2715

* TCM DTC P0716, P0717, P0722, P0723, or P182E is not set.

* ECM DTC P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, or P042E is not set.

* The accelerator pedal position is 0.5 percent or greater.

* The output speed is 16 RPM or greater.

* The ignition voltage is between 8.6-32 V.

* The engine speed is between 400-7500 RPM for 5 seconds.

* The transmission temperature is -6.6°C (20°F) or greater.

* The throttle position signal is valid.

* High side driver (HSD) is enabled.

* The PC solenoid 4 is commanded OFF, releasing the 2-6 clutch.

Conditions for Setting the DTC

P2714

The Transmission Control Module has detected an incorrect gear ratio or neutral condition when the 2-6 clutch is commanded ON. This condition must occur 3 times.

P2715

The Transmission Control Module has detected an incorrect gear ratio change when the 2-6 clutch is commanded OFF during a shift or when 2nd gear ratio is detected in 1st gear. This condition must occur 3 times.

Action Taken When the DTC Sets

P2714

* DTC P2714 is a Type A DTC.

* The TCM commands maximum line pressure.

* The TCM inhibits Tow/Haul mode.

* The TCM freezes transmission adaptive functions.

* The TCM inhibits TAP Up/Down function.

* The TCM inhibits Manual Up/Down Shift with the shift selector.

* The TCM limits the transmission to Reverse gear and 3rd gear operation.

P2715

* DTC P2715 is a Type A DTC.

* The TCM commands maximum line pressure.

* The TCM inhibits Tow/Haul mode.

* The TCM freezes transmission adaptive functions.

* The TCM inhibits TAP Up/Down function.

* The TCM inhibits Manual Up/Down Shift with the shift selector.

* The TCM limits the transmission to 2nd gear operation.

Conditions for Clearing the DIC/DTC

DTCs P2714 and P2715 are Type A DTCs.

Diagnostic Aids

Before performing a road test, configure and setup the scan tool for snapshot mode. This will allow you to display, monitor, and verify multiple transmission data parameters at one time, after the road test.

Reference Information

Connector End View Reference

* Component Connector End Views 5 Bow Lowered Switch (CM7)

* Inline Harness Connector End Views X102

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

Description and Operation

* Electronic Component Description Electronic Component Description

* Transmission General Description Transmission General Description

* Transmission Component and System Description Transmission Component and System Description

* Park - Engine Running Park - Engine Running

* Reverse Reverse

* Neutral - Engine Running Neutral - Engine Running

* Drive Range, First Gear Engine Braking First Gear Engine Braking

* Drive Range, First Gear First Gear

* Drive Range, Second Gear Second Gear

* Drive Range, Third Gear Third Gear

* Drive Range, Third Gear Default Third Gear Default

* Drive Range - Fourth Gear Fourth Gear

* Drive Range, Fifth Gear Fifth Gear

* Drive Range, Fifth Gear Default Fifth Gear Default

* Drive Range, Sixth Gear Sixth Gear

* Fluid Passages Fluid Passages

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References Control Module References for scan tool information

Special Tools

* DT-47825 - Control Solenoid Test Plate

* DT-47825-10 - Jumper Harness

For equivalent regional tools, refer to Special Tools Tools and Equipment.

Circuit/System Verification

Note: If other DTCs are set, diagnose those DTCs first.

1. Engine idling in Park position, with parking brake applied and drive wheels chocked.

2. Verify the transmission fluid level and condition is correct. Refer to Transmission Fluid Level and Condition Check Transmission Fluid Level and Condition Check.

3. Ignition ON, clear the TCM DTCs.

4. Verify the transmission operation performs as indicated in the road test instructions and DTCs P2714 or P2715 did not set. Refer to Road Test Initial Inspection and Diagnostic Overview.

• If DTCs P2714 or P2715 are set
Refer to Circuit/System Testing.

• If DTCs P2714 or P2715 did not set

5. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observe from the Freeze Frame/Failure Records data.

6. Verify the DTC does not set.

• If the DTC sets
Refer to Circuit/System Testing.

• If the DTC does not set

7. All OK.

Circuit/System Testing

1. Verify the transmission line pressures are within the specified ranges. Refer to Line Pressure Check Line Pressure Check.

• If the line pressures are not within the specified ranges
Refer to Fluid Pressure High or Low Fluid Pressure High or Low.

• If the line pressures are within the specified ranges

2. Ignition OFF. Remove the Q8 Control Solenoid Valve Assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly Replacement Service and Repair.

3. Verify a pressure change occurs for all solenoids when performing the solenoid test. Refer to Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test.

• If a pressure change does not occur for each solenoid
Replace the Q8 Control Solenoid Valve Assembly.

• If a pressure change does occur for each solenoid

4. Verify the conditions listed below do not exist. Carefully inspect each component for that condition. Repair or replace as necessary.

P2714 or P2715 - Control Valve Upper Body Assembly (304)

2-6 clutch regulator valve (334) stuck/sticky - debris, binding, damaged valve, or scored bore.

P2714 - Q8 Control Solenoid Valve Assembly (314)

Refer to document PIP 4304A. DTC P2714 may be set with DTC P0878.

P2714 or P2715 - Q8 Control Solenoid Valve Assembly (314)

* Control signal fluid supply leak-valve body filer plate assembly cracked or damage gasket seal.

* O-ring seals leaking.

P2714 or P2715 - Center (w/2-6 and Low/Rev Clutch) Support Assembly (67)

* 2-6 clutch return spring retaining ring (455) not seated in groove.

* 2-6 clutch piston assembly - seal damaged or leaking.

* 2-6 clutch plates (451-453) worn or damaged.

* Center support transfer seal assembly (20) incorrectly installed.

P2714 - 1-2-3-4 and 3-5-R Clutch Housing Assembly (51)

* 1-2-3-4 clutch backing plate retaining ring (429) not seated/oriented correctly.

* 1-2-3-4 clutch piston (414) - seals damaged or leaking.

* 1-2-3-4 clutch piston (414) - cracked or damaged.

P2714 - 4-5-6 (w/turbine shaft) Clutch Assembly (56)

* Turbine shaft fluid seal rings (442) damaged or leaking.

* 4-5-6 clutch piston assembly (439) - seals damaged or leaking.

P2714 - A/Trans Fluid Pump Cover Assembly (219)

Pump tower seals (230) damaged or leaking.

P2714 - Torque Converter (w/fluid pump) Housing Assembly (2)

Fluid pump housing/vanes/rotor/slide damaged/scored.

P2714 - A/Trans Fluid Filter Assembly (26)

Oil filter (26) or filter seal (25) loose or damaged.

Repair Instructions

Perform the Diagnostic Repair Verification Verification Tests after completing the repair.

* Perform the Reset Transmission Adapts Reset Procedure following all transmission related repairs.

* Refer to Control Module References Control Module References for control solenoid valve assembly replacement, programming, and setup.