B2485
DTC B2485
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provide an overview of each diagnostic category.
DTC Descriptors
DTC B2485 02
- Wireless Communication (BT) Antenna Circuit Short to Ground
DTC B2485 04
- Wireless Communication (BT) Antenna Circuit Open
Diagnostic Fault Information
Circuit/System Description
Bluetooth (R) wireless technology is a short-range communications technology intended to replace the cables connecting portable and/or fixed devices while maintaining high levels of security. The operating range of the signal is approximately 30 feet.
The Bluetooth (R) antenna is a small fixed antenna connected directly to the Telematics Communication Interface Control Module and is used to send and receive signals from a Bluetooth (R) enabled cellular phone. The antenna utilizes no cabling and is not external to the vehicle.
Conditions for Running the DTC
* The ignition is in OFF, ACCESSORY or RUN position.
* The system voltage is between 9-16 V.
* The Telematics Communication Interface Control Module tests the antenna once every second.
Conditions for Setting the DTC
B2485 02
* The signal voltage is less than 1 V.
* The above conditions must be met for 500 ms.
B2485 04
* The signal voltage is greater than 2 V.
* The above conditions must be met for 500 ms.
Actions Taken When the DTC Sets
* The OnStar (R) status LED turns red.
* Bluetooth (R) functionality is disabled.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Diagnostic Aids
* Verify the mobile device is properly configured for the feature being used. Refer to the device manufacturers information.
* Verify the function/feature that is being used is supported by the mobile device.
* The device must be paired to the Telematics Communication Interface Control Module to use the available Bluetooth (R) feature(s). The pairing process must only be performed once for each device, unless that device's information is deleted.
* The system can store pairing information for multiple devices, but can only be actively connected to one at any given time.
Reference Information
Schematic Reference
OnStar Schematics OnStar Schematics
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
OnStar Description and Operation OnStar
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Special Tools
EL-50334-20 - Multi-Media Interface Tester (Multi-Media Interface Tool)
Circuit/System Verification
1. Ignition ON.
2. Verify that DTC B2485 is not set.
• If DTC B2485 is set
Refer to Circuit/System testing
• If DTC B2485 is not set
3. All OK.
Circuit/System Testing
1. Verify that the T4S Wireless Communication Antenna - Bluetooth (R) is properly connected to the K73 Telematics Communication Interface Control Module and is not damaged.
• If the antenna is disconnected
Connect the T4S Wireless Communication Antenna - Bluetooth (R) to the module.
• If the antenna is damaged
Test or replace the T4S Wireless Communication Antenna - Bluetooth (R).
• If the antenna is connected and not damaged
Note: The Multi-Media Interface Tool tool can be used to test either cellular phone or streaming audio functions. Refer to the tool instructions, and perform the appropriate test(s) related to the customers concern in the following steps.
2. Ignition ON, infotainment system ON.
3. Verify the infotainment system successfully pairs with the Multi-Media Interface Tool.
• If the infotainment system does not successfully pair with the Multi-Media Interface Tool.
1. Test or replace the T4S Wireless Communication Antenna - Bluetooth (R).
2. Clear the DTC, ignition OFF.
3. Ignition ON.
4. Verify the DTC is not set.
• If the DTC is set, replace the K73 Telematics Communication Interface Control Module.
• If the DTC is not set
5. All OK.
• If the infotainment system successfully pairs with the Multi-Media Interface Tool.
4. All OK.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Wireless Communication Interface Antenna Replacement Service and Repair
* Control Module References Control Module References for Telematics Communication Interface Control Module replacement, programming and setup.