P0455

Circuit Description
The EVAP control system evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM monitors the vacuum level via the fuel tank pressure sensor input. The PCM turns ON the EVAP canister purge valve and the EVAP vent solenoid, allowing engine manifold pressure (vacuum) to draw a small vacuum on the entire Evaporative Emission system. If a sufficient vacuum cannot be sustained over a given period of time, a large leak (or a malfunction) is indicated with the DTC P0455.

The Evaporative Emission (EVAP) system as defined by federal regulation includes the following components:
^ Fuel tank
^ EVAP vent solenoid
^ Fuel tank pressure sensor
^ Fuel pipes and hoses
^ Vapor lines
^ Fuel filler cap
^ Fuel tank pressure control valve
^ Evaporative emission canister
^ Purge lines
^ EVAP canister purge valve

Condition for Running the DTC
The ignition is ON or the engine is running.

Conditions for Setting the DTC
Fuel tank pressure change:
^ Engine coolant temperature between 70°C (158°F) and 110°C (230°F)
^ Intake air temperature between -7°C (19°F) and 70°C (158°F)
^ Barometric pressure more than 75 kPa
^ Engine speed between 1,000 and 3,000 RPM (A/T), 1,000 and 3,500 RPM (M/T)
^ Fuel tank level is less than 75 percent
^ Difference between the maximum fuel tank internal pressure and the minimum pressure is less than the specified value

Diagnostic may take up to 20 minutes to run.

Action Taken When the DTC Sets
^ The Malfunction Indicator Lamp (MIL) will illuminate after two consecutive ignition cycles in which the diagnostic runs with the fault active.
^ The PCM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame buffer.

Conditions for Clearing the MIL/DTC
^ The MIL will turn off after three consecutive drive cycles without a fault present.
^ A DTC will clear after 40 consecutive warm-up cycles without a fault.
^ DTCs can be cleared by using a scan tool or by disconnecting the PCM battery feed.

Diagnostic Aids
A DTC P0455 is more likely to set during city driving. Avoid operating the vehicle for long periods on the highway when validating a DTC P0455.
The EVAP purge diagnostic checks for many of the faults that can cause a DTC P0455 to set. If the EVAP purge test passes the cause of the DTC P0455 is probably intermittent. Clear the DTCs. Road test the vehicle while monitoring the EVAP purge test in the MIL/System Status selection under System Information on the scan tool. When the EVAP purge test indicates complete with a YES status, check for a DTC P0455 under Last Test Failed. If there is no DTC P0455 indicated, the DTC is intermittent and the purge system diagnostic is indicating OK at this time.
Check for any of the following conditions:
^ A loose or missing fuel filler (gas) cap
^ Cracked or punctured EVAP canister
^ A damaged or disconnected source vacuum line, EVAP purge line, vent hose, or fuel tank vapor line
^ A faulty or erratic fuel tank pressure sensor can cause a DTC P0455 to set.

For functional checks of the components listed above, Refer to EVAP Control System Diagnosis. Component Tests and General Diagnostics

An intermittent malfunction may be caused by a fault in any of the EVAP control system electrical circuits. Inspect the wiring harness and components for any of the following conditions:
^ Backed out terminals
^ Improper mating of terminals
^ Broken electrical connectors locks
^ Improperly formed or damaged terminals
^ Faulty terminal to wire connections
^ Physical damage to the wiring harness
^ A broken wire inside the insulation
^ Corrosion of electrical connections, splices, or terminals

If the DTC P0455 is intermittent, driving the vehicle under the following conditions can verify whether the fault is present. Perform the scan tool Clear DTC Information function. Road test the vehicle while monitoring the DTC P0455 diagnostic on the scan tool under the Not Ran Since Code Cleared selection in the DTC Information menu. If a DTC P0455 appears in the Not Ran Since Code Cleared list, the P0455 diagnostic has not yet run. When the DTC P0455 does not appear in the Not Ran Since Code Cleared list, the P0455 diagnostic has run. If the MIL is NOT ILLUMINATED and there is no PENDING DTC Status in DTC Information, the P0455 diagnostic has passed. DTCs MUST BE CLEARED in order to view the CURRENT STATUS of the Not Ran Since Code Cleared list. DO NOT FORGET that the Not Ran Since Code Cleared list only indicates that the test has run, not whether the test passed or failed. The DTC Information screen must be checked for CURRENT or PENDING status, in order to determine the outcome of the diagnostic test involved.

If the DTC P0455 cannot be duplicated, the information included in the Freeze Frame data can be useful in determining vehicle operating conditions when the DTC was first set.

Test Description
The numbers below refer to the step numbers in the diagnostic table.
1. The Powertrain OBD System Check prompts the technician to complete some basic checks and to store the Freeze Frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
2. If any other EVAP DTCs except a DTC P0440 are set, diagnose those DTCs first.
6. This step checks the operation of the EVAP tank pressure control solenoid valve. The EVAP tank pressure control solenoid vacuum valve output control is disabled by the PCM when any DTCs are stored and when engine speed is indicated.
9. This step checks the EVAP tank pressure control solenoid valve control circuit. A short to ground will keep the EVAP solenoid open and cause the system to fail. The EVAP tank pressure control solenoid vacuum valve output control is disabled by the PCM when any DTCs are stored and when engine speed is indicated.
10. This step checks the components that supply manifold vacuum to the EVAP canister purge valve. A plugged or leaking EVAP canister surge tank could prevent vacuum from reaching the EVAP canister purge valve.
11. This step checks the operation of the EVAP canister purge valve. The EVAP canister purge valve duty cycle control is disabled by the PCM when any DTCs are stored and when engine speed is indicated.
15. This step checks the operation of the EVAP canister vent solenoid. Output controls can be found on the scan tool under Special Functions. The EVAP canister vent solenoid output control is disabled by the PCM when any DTCs are stored or when engine speed is indicated.
18. This step checks the EVAP canister vent solenoid control circuit. The EVAP canister vent solenoid output control is disabled by the PCM when any DTCs are stored and when engine speed is indicated.
19. This step uses tools from the EVAP Pressure/Purge Cart Diagnostic Station, in order to determine whether EVAP control system is sealed sufficiently to be pressurized. Any leak that is found must be located and repaired before continuing with the diagnosis.
20. Use the ultrasonic leak detector in order to locate any leaks after pressurizing the EVAP system.
22. This step checks the EVAP canister for blockage or restrictions.
35. The DTC P0455 diagnostic can be monitored on the scan tool under the MIL/System Status selection of System Information. When the EVAP purge test displays a YES status (indicating that the purge system diagnostic is completed) check for a DTC P0455 in the Last Test Failed screen of the scan tool. If there is no DTC P0455 displayed the EVAP purge system diagnostic has run and passed, indicating that no malfunction was present this time. DTCs MUST BE CLEARED in order to view the CURRENT STATUS of the system diagnostics being performed. Do not forget that the MIL/System Status tests only indicate that the test has run, not whether the test passed or failed. The Last Test Failed screen must be checked for related DTCs in order to determine the outcome of the diagnostic test involved.