Crankshaft, Engine

Crankshaft Bearing Cap Bolts
(Inner Bolts 12 mm) First Pass 75 Nm (55 ft. lbs.)
(Inner Bolts 12 mm) Second Pass 75 Nm (55 ft. lbs.)
(Inner Bolts 12 mm) Final Pass 90 °
(Outer Bolts 12 mm) First Pass 20 Nm (15 ft. lbs.)
(Outer Bolts 12 mm) Second Pass 20 Nm (15 ft. lbs.)
(Outer Bolts 12 mm) Final Pass 90°
(Outer Bolt 10 mm) 10 Nm (30 ft. lbs.)
Crankshaft Bore
I.D. White 79.826-79.834 mm (3.1427-3.1430 inch)
I.D. Red/Orange 79.834-79 842 mm (3.1430-3.1433 inch)
I.D. Blue 0.842-79.850 mm (3.1433-3.1437 inch)
Out-of-Round 0.0130 mm maximum (0.0005 inch maximum)
Crankshaft Journal (Main)
OD (White) (1-4) 74.9330-74.9410 mm (2.9501-2.9504 inch)
OD (White) (5) 74.9280-74.9360 mm (2.9251-2.9502 inch)
OD (Orange or Red)(1-4) 74.9250-74.9330 mm (2.9498-2.9501 inch)
OD (Orange or Red) (5) 74.9200-74.9280 mm (2 9496-2.9499 inch)
OD (Blue) (1-4) 74.9170-74.9250 mm (2,9494-2.9498 inch)
OD (Blue) (5) 74.9120-74.9200 mm (2.9494-2.9498 inch)
Taper 0.0830 mm maximum (0.0033 inch maximum)
Out-of-Round 0.0830 mm maximum (0.0033 inch maximum)
Bearing Clearance (1-4) 0.0450-0.0830 mm 0.0018-0.0033 inch
Bearing Clearance (5) 0.0550-0.0920 mm (0.0022-0.0037 inch)
Crankshaft Journal (Rod)
OD (Yellow) 60.9260-60.9390 mm (2.3987-2.3992 inch)
OD (Green) 60.9130-60 9260 mm (2.3990-2.4000 inch)
Taper 0.0050 mm maximum (0.0002 inch maximum)
Out-of-Round 0.0050 mm maximum (0.0002 inch maximum)
Bearing Clearance 0.0350-0.0940 mm (0.0014-0.0037 inch)
Side Clearance (Rod) 0.1700-0.630 mm (0.0067-0.0250 inch)
End Play (Crankshaft) 0.1050-0.2850 mm (0.0040-0.0110 inch)
Crankshaft Bearing (Main)-Select Fit: Refer to Crankshaft and Bearings Installation on page 6-797 for proper crankshaft cross-referencing
White (1) STD inch Case, STD inch Cap, (STD inch Case STD inch Cap)
White (2) 0.013 mm U S. inch Case, STD in Cap (0.0005 inch U.S. inch Case STD in Cap)
White (3) 0.026 mm U.S. inch Case,STD in Cap (0.0010 inch U.S. inch Case, (STD in Cap)
Orange or Red (1) STD inch Case,0.013 mm U.S. in Cap (STD in Case.0.0005 inch U.S. inch Cap)
Orange or Red (2) 0.013 mm U.S. in Case,0.013 mm U.S. in Cap (0.0005 in U.S. in Case, (0.0005 U.S. inch Cap)
Orange or Red (3) 0.026 mm U S in Case, 0.0013 mm U.S Cap (0.0010 in U.S. in Case, 0.0005 in U.S. in Cap)
Blue (1) STD inch Case 0.026 mm U.S. inch Cap (STD in Case,0.0010 in U.S cap)
Blue (2) 0.013 mm U.S. in Case. 0.026 mm U.S. in Cap,(0.0005 in U.S. in Case, 0.0010 in U.S. in cap)
Blue (3) 0.026 mm U.S. in Case, 0.026 mm U.S. in cap(0.0010 in U.S in Case, 0.0010 in U.S. in cap)
Crankshaft Bearing (Rod) Select Fit: Refer to Crankshaft and Bearings Installation 017 page 6- 79Z for proper crankshaft cross-referencing.
Yellow STD inch Rod, STD in Cap (STD in Rod, STD in Cap)
Green STD inch Rod 0.026 mm U.S. in cap (STD inch Rod 0.0010 in U.S in Cap)