Cylinder Head Replacement - Left

Cylinder Head Replacement - Left

^ Tools Required
- J 45059 Angle Meter

Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the cooling.
3. Remove the drive belt.





4. Loosen the nut holding the power steering pump rear bracket to the side of the engine.
5. Remove the nut holding the power steering pump rear bracket to the front of the engine
6. Remove the three bolts and the nut holding the power steering pump mounting bracket to the engine.
7. With the power steering pump and the A/C compressor still attached, slide the power steering pump mount bracket off of the stud and set aside.





8. Remove the power steering pump mounting bracket stud from the cylinder head.
9. Remove the lower intake manifold.
10. Remove the exhaust manifold.





11. Remove the spark plug wire harness and the spark plug wire support.
12. Remove the valve pushrods.





13. Remove the ground wire bolt and the ground wire from the rear of the cylinder head.
14. Secure the ground wire out of the way.
15. Remove the bolt holding the fuel pipe bracket to the rear of the cylinder head.





16. Remove the engine coolant temperature sensor.
17. Remove the spark plugs.





18. Remove the cylinder head bolts.





19. Notice: After removal, place the cylinder head on two wood blocks to prevent damage to the sealing surfaces.

Remove the cylinder head.





20. Remove and discard the cylinder head gasket.





21. Remove the dowel pins (cylinder head locator), if required.
22. Clean the engine block and the cylinder head sealing surfaces.

23. Notice: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.

Clean the cylinder head bolts and the engine block bolt holes.

Installation Procedure





1. Inspect the dowel pins (cylinder head locator) for proper installation.





2. Important: Do not use any type sealer on the cylinder head gasket, unless specified.

Install the NEW cylinder head gasket in position over the dowel pins (cylinder head locator).





3. Install the cylinder head onto the engine block. Guide the cylinder head carefully into place over the dowel pins and the cylinder head gasket.





4. Apply sealant GM P/N 12346004 (Canadian P/N 10953480) or equivalent to the threads of the cylinder head bolts.
5. Install the cylinder head bolts finger tight.





6. Notice: Refer to Fastener Notice in Service Precautions.

Tighten the cylinder head bolts in sequence on the first pass.
^ Tighten the bolts in sequence on the first pass to 30 Nm (22 ft. lbs.).
7. Use the J 45059 in order to tighten the cylinder head bolts in sequence.
^ Rotate the long bolts (1, 4, 5, 8, and 9) an additional 75 degrees.
^ Rotate the medium bolts (12 and 13) an additional 65 degrees.
^ Rotate the short bolts (2, 3, 6, 7, 10, and 11) an additional 55 degrees.
8. Install the spark plugs.





9. If reusing the engine coolant temperature sensor (if applicable), apply sealant GM P/N 12346004 (Canadian P/N 10953480) or equivalent to the threads of the engine coolant temperature gage sensor.
10. Install the engine coolant temperature sensor.
^ Tighten the engine coolant temperature sensor to 20 Nm (15 ft. lbs.).
11. Install the valve pushrods.
12. Install the lower intake manifold.
13. Install the exhaust manifold.





14. Install the spark plug wire harness and spark plug wire support.
^ Tighten the support bolts to 12 Nm (106 inch lbs.).





15. Install the bolt for and the fuel pipe bracket to the rear of the cylinder head.
^ Tighten the fuel pipe bracket bolt to 30 Nm (22 ft. lbs.).
16. Install the ground wire and the ground wire bolt to the rear of the cylinder head.
^ Tighten the ground wire bolt to 35 Nm (26 ft. lbs.).





17. Install the stud for the power steering pump mounting bracket to the cylinder head.
^ Tighten the power steering pump mounting bracket stud to 20 Nm (15 ft. lbs.).





18. Slide the power steering pump mounting bracket with the power steering pump and the A/C compressor on the stud.
19. Position the power steering pump rear bracket on the studs.
20. Install the power steering pump mounting bracket three bolts and the nut.
21. Install the nut for the power steering pump rear bracket to the front of the engine.
^ Tighten the power steering pump mounting bracket and the power steering pump rear bracket bolts and the nuts to 41 Nm (30 ft. lbs.).
22. Install the drive belt.
23. Fill the cooling system.
24. Connect the negative battery cable.