Engine Oil Cooler Hose/Pipe Replacement

Engine Oil Cooler Hose/Pipe Replacement (4WD)

Removal Procedure
The optional oil cooler is either an integral part of the radiator or a separate unit placed in front of the radiator. The cooler lines and hoses are serviceable.





1. Disconnect the engine oil cooler quick connect fittings.
2. If equipped with a 5.3L or 6.0L engine, perform the following:
1. Open the oil cooler hose clip located on the lower fan shroud.
2. Remove the oil cooler hoses from the clip.

3. Raise and suitably support the vehicle.





4. If equipped with a 8.1L engine, perform the following:
5. Remove the oil cooler hoses from the clip.
6. Raise and suitably support the vehicle.
7. Place jack or utility stands at the rear of the vehicle.
8. If equipped, remove the engine protection shield.
9. If equipped, remove the front differential carrier shield.





10. Place an adjustable jack under the front differential carrier.
11. Remove the inner axle housing nuts and washers from the bracket.





12. Remove the differential carrier upper mounting bolt and nut.
13. Pivot the differential carrier forward and down on the lower mount bolt while it is being supported by the adjustable jack.
14. Secure the differential carrier to the jack.





15. Remove the differential carrier lower mounting bolt and nut.
16. Lower the jack 4 to 6 inches.





17. If equipped with a 5.3L or 6.0L engine, perform the following:
1. Remove the oil cooler hose bracket bolt (1).
2. Remove the oil cooler hose adapter bolts (2).
3. Remove the oil cooler hose assembly and gasket. Discard the gasket.
4. Inspect the fittings, connectors and cooler hoses for damage or distortion.





18. If equipped with a 8.1L engine, perform the following:
1. Remove the oil cooler hose bracket bolt.
2. Disconnect the quick connect fittings (1) at the engine.
3. Remove the oil cooler hose assembly. Discard the gasket.
4. Inspect the fittings, connectors and cooler hoses for damage or distortion.

Installation Procedure





1. If equipped with a 8.1L engine, perform the following:
1. Install the oil cooler hose assembly and a NEW gasket.
2. Connect the quick connect fittings (1) at the engine.
3. Install the oil cooler hose bracket bolt.
Tighten the bolt to 50 Nm (37 ft. lbs.).

Notice: Refer to Fastener Notice in Service Precautions.

Important: A distinct snap should be heard when assembling the tube ends of the hose assembly to the quick connectors. To ensure the tube is fully inserted into the connector, check by giving the tube a forceful pull.






2. If equipped with a 5.3L or 6.0L engine, perform the following:
1. Install the oil cooler hose assembly and a NEW gasket.
2. Install the oil cooler hose adapter bolts (2).
Tighten the bolts to 12 Nm (106 inch lbs.).
3. Install the oil cooler hose bracket bolt (1).
Tighten the bolt to 25 Nm (18 ft. lbs.).





3. Raise the jack in order to position the differential carrier.
4. Install the differential carrier lower mounting bolt and nut. Do not tighten the bolt at this time.
5. Pivot the differential carrier up and back on the lower mount bolt while it is being supported by the jack.





6. Install the differential carrier upper mounting bolt and nut. Do not tighten the bolt at this time.





7. Install the inner axle housing washers and nuts to the brackets.
^ The inner axle housing bolts to 100 Nm (75 ft. lbs.).
^ The upper and lower differential carrier bolts to 100 Nm (75 ft. lbs.).

8. Remove the adjustable jack from under the front differential carrier.
9. If equipped, install the front differential carrier shield.
10. If equipped, install the engine protection shield.
11. Remove the jack or utility stands from the rear of the vehicle.
12. Lower the vehicle.





13. If equipped with a 8.1L engine perform the following:
14. Install the oil cooler hoses to the clip.

Important:
^ Ensure the oil cooler line being installed has a plastic cap on the end that connects to the quick connect fitting. If no plastic cap exists, or the plastic cap is damaged, obtain a new cap. Install the cap onto the cooler line prior cooler line installation.
^ Do not use the plastic cap in order to install the cooler line into the fitting.






15. If equipped with a 5.3L or 6.0L engine, perform the following:
0. Install the oil cooler hoses to the hose clip on the fan shroud.
1. Snap the oil cooler hose clip shut.

16. Connect the engine oil cooler quick connect fittings.