Heating and A/C Operation

AIR TEMPERATURE DESCRIPTION AND OPERATION

The air temperature controls are divided into 7 areas:
- HVAC Control Components
- Heating and A/C Operation
- Auxiliary Heating and A/C Operation
- Automatic Operation
- Steering Wheel Controls
- Engine Coolant
- A/C Cycle

Heating and A/C Operation
The purpose of the heating and A/C system is to provide heated and cooled air to the interior of the vehicle. The A/C system will also remove humidity from the interior and reduce windshield fogging. The vehicle operator can determine the passenger compartment temperature by adjusting the air temperature switch. The vehicle passenger can offset the passenger temperature as much as 16.7 °C (30 °F). Regardless of the temperature setting, the following can effect the rate that the HVAC system can achieve the desired temperature:
- Recirculation actuator setting
- Difference between inside and desired temperature
- Difference between ambient and desired temperature
- Blower motor speed setting
- Mode setting
- Auxiliary HVAC settings

The control module makes the following actions when automatic operation is not selected, and an air temperature setting is selected:
- When the air temperature switch is placed in the warmest position, the control module commands the air temperature door to divert maximum air past the heater core.
- When the air temperature switch is placed in the coldest position, the control module commands the air temperature door to direct air to bypass the heater core.
- When the air temperature switch is placed between the warmest and coldest positions, the control module monitors the following sensor inputs to determine the air temperature door position that diverts the appropriate amount of air past the heater core in order to achieve the desired temperature:
- Sunload
- Duct temperatures
- Ambient temperature
- Inside temperature

The A/C system can be engaged by either pressing the A/C switch or during automatic operation. The HVAC control module sends a class 2 message to the powertrain control module (PCM) for A/C compressor engagement. The PCM will provide a ground for the A/C compressor relay enabling it to close its internal contacts to send battery voltage to the A/C compressor clutch coil. The A/C compressor diode will prevent a voltage spike, resulting from the collapse of the magnetic field of the coil, from entering the vehicle electrical system when the compressor is disengaged.

The following conditions must be met in order for the A/C compressor clutch to turn ON:
- The ambient air temperature is above 1 °C (35 °F).
- The A/C low pressure switch signal circuit is grounded.
- The A/C refrigerant pressure sensor parameter is less than 2 413 kPa (350 psi).
- The A/C compressor temperature switch contacts are closed.
- The PCM receives an A/C request from the HVAC control module.
- The engine coolant temperature (ECT) is less than 123 °C (253 °F).
- The engine RPM is more than 550 RPM.
- The throttle position is less than 100 percent.

The HVAC control module monitors the A/C low pressure switch signal circuit. If the voltage signal on this circuit has no voltage drop, the module will interpret this condition as a low pressure, disabling the A/C request. The A/C low pressure switch will open its internal contacts at 151 kPa (22 psi). Then close the contacts at 275 kPa (40 psi) to resume A/C operation. This switch assists in cycling the A/C compressor and prevents A/C compressor operation if system has a low refrigerant level.

The PCM monitors the A/C refrigerant pressure sensor signal circuit. The voltage signal on this circuit is proportional to the refrigerant pressure inside the A/C high side pressure line. As the pressure inside the line increases, so does the voltage signal. If the pressure is above 2 413 kPa (350 psi), the A/C compressor output is disabled. When the pressure lowers to 1578 kPa (229 psi), the PCM enables the compressor to operate.

The sensor information is used by the PCM to determine the following:
- The A/C high side pressure
- An A/C system load on the engine
- An excessive A/C high side pressure
- The heat load at the A/C condenser

The A/C compressor has an A/C compressor temperature switch. This switch protects the compressor from over heating. The switch interrupts power to the compressor clutch coil. When the compressor core temperature rises above 135 °C (275 °F), the switch opens, disabling the compressor clutch coil. When the temperature lowers to 120 °C (248 °F), the switch closes, enabling the compressor clutch coil. This switch is not a serviceable part, it is integral to the A/C compressor.

Once engaged, the compressor clutch will be disengaged for the following conditions:
- The ambient air temperature is less than 1 °C (35 °F).
- The A/C compressor temperature switch contacts are open.
- The throttle position is 100 percent.
- The A/C low pressure switch is open.
- The A/C high side pressure is more than 2 413 kPa (350 psi).
- The A/C low side pressure is less than 151 kPa (22 psi).
- The engine coolant temperature (ECT) is more than 123 °C (253 °F).
- The engine speed is more than 5,500 RPM.
- Transmission shift
- The PCM detects excessive torque load.
- The PCM detects insufficient idle quality.
- The PCM detects a hard launch condition.