Operation CHARM: Car repair manuals for everyone.
Home >> Chevy Truck >> 2009 >> HHR L4-2.4L >> Repair and Diagnosis >> Wiper and Washer Systems >> Testing and Inspection >> Symptom Related Diagnostic Procedures >> Washer Malfunction (Front Washers)

Washer Malfunction (Front Washers)




Washer Malfunction (Front Washers)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview)provides an overview of each diagnostic category.

Diagnostic Fault Information





Circuit/System Description

The Windshield Wiper Washer Switch controls the washer pump motor by applying accessory voltage through the windshield washer pump control circuit. The BCM monitors the Windshield washer pump control circuit and when a wash cycle is requested the BCM will command the low speed wipers ON for 3 wipe cycles. The washer pump is a bidirectional pump and is used for both the front and rear washer. When the front washers are requested the WSW PUMP Relay applies power to the washer pump and uses the circuitry of the REAR WSW PUMP Relay to ground the washer pump motor through ground circuit G109.

Reference Information
Schematic Reference

Wiper/Washer Schematics ([1][2]Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Wiper/Washer System Description and Operation (Front ) (Wiper/Washer System Description and Operation (Front ))Wiper/Washer System Description and Operation (Rear) (Wiper/Washer System Description and Operation (Rear))
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, wiper switch in the OFF position, observe the scan tool Windshield Washer Switch parameter while cycling the WASH switch ON and OFF. The parameter should cycle between Active and Inactive.

• If the parameter does not cycle between the specified values, refer to Windshield Wiper/Washer Switch Circuit Malfunction.

2. Operate the washers using the WASH switch. Verify the washer pump activates and the low speed wipers turn on.

• If the washer pump does not activate, refer to Washer Pump Circuit Malfunction.
• If the low speed wipers do not turn on, refer to Windshield Wiper System Malfunction (Windshield Wiper System Malfunction).

Circuit/System Testing

Windshield Wiper/Washer Switch Circuit Malfunction
1. Ignition OFF, disconnect the harness connector at the Windshield Wiper/Washer switch.
2. Ignition ON, test for 12 volts between accessory voltage circuit terminal D and ground.

• If not the specified value, test the accessory voltage circuit terminal D for a short to ground. If the circuit tests normal, replace the BCM.

3. Ignition ON, verify the scan tool Windshield Washer Switch parameter is Inactive.

• If not the specified value, test the control circuit terminal B for a short to B+. If the circuit tests normal, replace the BCM.

4. Install a 3A fused jumper wire between the control circuit terminal B and B+. Verify the scan tool Windshield Washer Switch parameter is Active.

• If not the specified value, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

5. If all circuits test normal, test or replace the Windshield Wiper/Washer switch.

Washer Pump Circuit Malfunction
1. Ignition OFF, Disconnect harness connector at Windshield Washer Fluid Pump.
2. Ignition ON, test for B+ at control circuit terminal A of Windshield Washer Fluid Pump connector while activating washers.

• If not the specified value, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

3. Install a test light between control circuit terminal A and ground circuit terminal B at the windshield washer fluid pump connector
4. The test lamp should turn ON and OFF when the windshield washers are commanded ON and OFF.

• If not the specified value, test the ground circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

Component Testing

Multifunction Switch
1. With the WASH switch in the open position, test for infinite resistance between the Accessory Voltage terminal D and the control terminal B.

• If not the specified value, replace the multifunction switch.

2. With the WASH switch in the closed position, test for less than 2 ohms between the Accessory Voltage terminal D and the control terminal B.

• If greater than the specified range, replace the multifunction switch.

Washer Pump
1. Ignition OFF, disconnect the harness connector at the washer pump.
2. Install a 10A fused jumper wire between the control terminal A and 12 volts. Install a jumper wire between the ground terminal B and ground.
3. Verify the washer pump is activated.

• If the washer pump does not activate , replace the washer pump.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Turn Signal Multifunction Switch Replacement (Turn Signal Multifunction Switch Replacement)
* Underhood Electrical Center or Junction Block Replacement (Underhood Electrical Center or Junction Block Replacement)
* Washer Pump Replacement (Service and Repair)
* Control Module References (Programming and Relearning)for BCM replacement, setup, and programming

pro multis · About Operation CHARM