P2271
DTC P2271 or P2273
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P2271
- HO2S Signal Stuck Rich Bank 1 Sensor 2
DTC P2273
- HO2S Signal Stuck Rich Bank 2 Sensor 2
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The control module supplies the HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started, the control module operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream. Low HO2S voltage indicates a lean exhaust stream.
Conditions for Running the DTC
* Before the ECM can report DTC P2271, or P2273 failed, DTCs P013A, P013C, P013E, P014A, P2270, and P2272 must run and pass.
* DTCs P0036, P0037, P0038, P0137, P0138, P0140, P0141, P0443, P0458, P0459, P2232 are not set.
* The ignition voltage is between 10-32 volts.
* The engine speed is between 900-2,500 RPM.
* The mass air flow (MAF) is between 3-20 g/s.
* The vehicle speed is between 70-130 km/h (43.5-80.8 mph).
* The fuel level is greater than 10 percent.
* The fuel system is in Closed Loop.
* The catalytic converter temperature is between 550-900°C (1,022-1,652°F).
* The accelerator pedal position (APP) is steady.
* The torque converter clutch is TCC is applied.
* The DTCs run once per ignition cycle during decel fuel cut-off when the above conditions are met. DTCs are allowed to run more than once per ignition cycle after a code clear or an ECM reflash.
Conditions for Setting the DTC
The ECM does not detect an HO2S voltage less than 100 mV before accumulated mass air flow exceeds 90 grams.
Action Taken When the DTC Sets
DTCs P2271 or P2273 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P2271 or P2273 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (LZ1) [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Connector Views
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description Hybrid Modes of Operation Description.
2. Ignition ON, verify the scan tool hood position parameter displays Open.
• If the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle for DTC P254F.
3. Ignition ON, observe the DTC information with a scan tool. Verify that no HO2S heater DTCs are set.
• If any HO2S heater DTCs are set, perform those diagnostics first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, open the hood to disable the Auto-Stop function.
2. Disconnect the harness connector at the appropriate HO2S.
3. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm between the low reference circuit terminal A and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
4. Ignition ON, verify the appropriate scan tool HO2S parameter is approximately 450 mV.
• If less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the ECM.
• If greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
5. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S parameter is less than 60 mV.
• If greater than the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, replace the ECM.
6. Verify none of the following conditions exist:
* Rich fuel injectors-Refer to Fuel Injector Diagnosis (CH47976) Fuel Injector Diagnosis (J39021 or Scan Tool)
* Water intrusion in the HO2S harness connector
* High fuel system pressure-Refer to Fuel System Diagnosis.
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis Testing and Inspection
* Fuel saturation of the evaporative emission (EVAP) canister
• If you find any of the above conditions, repair as necessary.
7. If all circuits test normal, replace the appropriate HO2S.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) Service and RepairHeated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) Service and Repair
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) Service and RepairHeated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) Service and Repair
* Perform the scan tool Heated Oxygen Sensor Resistance Learn Reset after replacing a HO2S.
* Control Module References Control Module References for ECM replacement, , programming and setup.