Antenna - Installation
INSTALLATION
RADIO
1. Position the antenna body and cable (5) in the opening between the right cowl side outer panel and the fender.
2. Push the antenna coaxial cable into the passenger compartment through the hole in the right cowl side outer panel.
3. Engage the antenna coaxial cable grommet in the hole, in the right cowl side outer panel.
4. Position the antenna body through the mounting hole in the top of the fender.
5. Install the adapter (4) over the antenna body from the top of the fender.
6. Install and tighten the antenna cap nut (3) using an antenna nut wrench special tool C-4816.
7. Install and tighten the antenna mast (2), onto the antenna body.
8. Engage the antenna coaxial cable retainers at the right cowl side inner panel and inside the right front fender.
9. Engage the antenna coaxial cable and the retainer clips on the lower instrument panel support and the glovebox.
10. Reach under the instrument panel outboard of the glove box to reconnect the antenna coaxial cable connector (2).
11. Install the cowl trim cover.
12. Install the wheelhouse splash shield.
13. Connect the negative battery cable.
SATELLITE AUDIO ONLY
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Install the radio Radio - Installation.
3. Install the glove box Instrument Panel Glove Box - Installation.
4. Install the passenger side cowl panel Cowl Trim Panel - Description.
5. Install the passenger side quarter trim panel Quarter Trim Panel - Installation.
6. Install the passenger side c-pillar C-Pillar Trim Panel-Installation.
7. Install the antenna base in the roof of the vehicle.
SATELLITE AUDIO/VIDEO
AUDIO ANTENNA TO MODULE
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Install the antenna base to the roof of the vehicle. Tighten to 9 Nm (80 in. lbs.).
3. Connect the antenna cable to the module (2).
4. Raise the rear portion of the headliner Headliner - Installation.
5. Connect the battery negative cable.
VIDEO CABLE FROM VIDEO ANTENNA TO COWL
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Connect the antenna cable to the video antenna.
3. Connect the antenna cables together in the cowl.
4. Install the passenger side cowl panel Cowl Trim Panel - Description.
5. Raise the front portion of the headliner Headliner - Installation.
VIDEO CABLE FROM COWL TO MODULE
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Raise the rear portion of the headliner Headliner - Installation.
3. Install the passenger side quarter trim panel Quarter Trim Panel - Installation.
4. Install the passenger side c-pillar C-Pillar Trim Panel-Installation.
5. Install the passenger side cowl panel Cowl Trim Panel - Description.
6. Install the passenger side scuff plates Description and Operation.
7. Connect the negative battery cable.
SIGNAL CABLE FROM RADIO TO COWL
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Install the radio Radio - Installation.
3. Install the glove box Instrument Panel Glove Box - Installation.
4. Install the passenger side cowl panel Cowl Trim Panel - Description.
5. Connect the negative battery cable.
SIGNAL CABLE FROM COWL TO LIFTGATE HEADER
NOTE: The antenna cables are integrated into the body harnesses. New antenna cables come as a overlay to the body harness.
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Raise the rear portion of the headliner Headliner - Installation.
3. Install the passenger side c-pillar C-Pillar Trim Panel-Installation.
4. Install the passenger side quarter trim panel Quarter Trim Panel - Installation.
5. Install the passenger side cowl panel Cowl Trim Panel - Description.
6. Install the passenger side scuff plates Description and Operation.
7. Connect the negative battery cable.
SIGNAL CABLE FROM LIFTGATE HEADER TO MODULE
1. Connect, route and secure the new antenna harness alone the same route as the old antenna cable.
2. Connect the cable to the module and the cable leading to the cowl.
3. Raise the rear portion of the headliner Headliner - Installation.
4. Connect the negative battery cable.