Brakes - Vehicle Surge While Speed Control is Engaged
NUMBER: 08-035-00GROUP: Electrical
DATE: Nov. 10, 2000
SUBJECT:
Vehicle Surge While Speed Control Is Engaged
OVERVIEW:
This bulletin involves installing a new antilock brake control module.
MODELS:
2001 (AN) Dakota
2001 (DN) Durango
NOTE:
THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH SPEED CONTROL (SALES CODE NHM) AND FOUR WHEEL ANTILOCK BRAKES (SALES CODE BGK) BUILT ON OR BEFORE THE ILLUSTRATED DATES:
SYMPTOM/CONDITION:
The vehicle surges while the speed control is engaged at 74 - 76 km/h (46 - 47 mph) and/or at 109 - 111 km/h (68 - 69 mph).
DIAGNOSIS/REPAIR PROCEDURES:
Road test the vehicle in a location where vehicle speeds of 74 - 76 km/h (46-47 mph) and/or 109 - 111 km/h (68 - 69 mph) can be maintained safely. Set the speed control at 74 - 76 km/h (46 - 47 mph) or at 109 - 111 km/h (68 - 69 mph). If the vehicle surges, disengage the speed control. If the vehicle still surges, further diagnosis is required. If the vehicle surges only while the speed control is engaged, perform the Repair Procedure.
NOTE:
DUE TO THE NATURE OF THIS CONDITION, IT MAY BE DIFFICULT TO DUPLICATE THE SYMPTOM. IF THE CUSTOMER INDICATES THAT THE VEHICLE SURGES AT 74 - 76 KM/H (46 - 47 MPH) AND/OR AT 109 - 111 KM/H (68 - 69 MPH) ONLY WHEN THE SPEED CONTROL IS ENGAGED, PERFORM THE REPAIR PROCEDURE.
PARTS REQUIRED:
NOTE:
ANTILOCK BRAKE CONTROLLER AVAILABILITY IS RESTRICTED. THE STAR CENTER MUST BE CONTACTED TO GET AUTHORIZATION AND TO ORDER A CONTROLLER. THE STAR CENTER'S PHONE NUMBER IS 1-800-850-STAR (7827). WHEN THE AUTOMATED ANSWERING SYSTEM REQUESTS A GROUP SELECTION, SELECT BRAKES AND THEN SELECT THE KELSEY HAYES GROUP
EQUIPMENT REQUIRED:
REPAIR PROCEDURE:
THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLER'S MOBILE SERVICE PROGRAM AND DOES NOT REQUIRE HOISTS OR OTHER FULL SERVICE FACILITY SPECIAL EQUIPMENT.
NOTE:
ONCE THE ANTILOCK BRAKE CONTROL MODULE (CAB) IS REPLACED, THE REAR AXLE TYPE AND TIRE SIZE MUST BE PROGRAMED INTO THE NEW CAB.
1. Disconnect battery negative cable.
2. Push the harness connector locks to release the locks, (Fig. 1) then remove the connectors from the CAB.
3. Disconnect the pump motor connector (Fig. 2).
4. Remove screws attaching CAB to the Hydraulic control Unit (HCU) (Fig. 3).
5. Remove the CAB.
6. Place the new CAB onto the HCU (see Parts Required section).
NOTE:
ENSURE THE CAB SEAL IS IN POSITION BEFORE INSTALLATION.
7. Install the mounting screws and tighten to 4-4.7 N.m (36-42 in. lbs.).
8. Connect the pump motor harness.
9. Connect the harnesses to the CAB and lock the connectors.
10. Connect battery.
NOTE:
THE NEW CAB MUST HAVE THE TIRE SIZE AND AXLE TYPE PROGRAMMED INTO THE NEW CONTROLLER IN ORDER TO HAVE THE CONTROLLER COMMUNICATE THE PROPER VEHICLE SPEED. FAILURE TO PROPERLY PROGRAM THE REPLACEMENT CAB WILL RESULT IN A BLINKING ABS INDICATOR.
11. Inspect rear tires to determine tire sizes.
12. Determine which rear axle type is used on this vehicle. Refer to the following graphics to help in identifying axle types (Fig. 4) (Fig. 5).
13. Using the DRBIII(R) select: MISC in the Antilock Brake menu. Then, SET PINION FACTOR.
NOTE:
THE DRBIII(R) MENU SCREEN CAN ONLY PROGRAM PRODUCTION SIZE TIRES THAT WERE CERTIFIED FOR THE VEHICLE WHEN THE VEHICLE WAS MANUFACTURED. IF THE TIRES ON THE VEHICLE DO NOT MATCH TIRE SIZES AVAILABLE ON THE DRBIII(R) MENU SCREEN, THEN THE TIRE ON THE VEHICLE WAS NEVER CERTIFIED FOR USAGE.
14. Turn the ignition switch to the RUN position (engine not running).
15. With the DRBIII(R), program the correct tire size and rear axle type.
16. Road test the vehicle above 48 km/h (30 mph) for at least two minutes to ensure that the antilock brake system functions as designed. If the ABS warning lamp illuminates during the road test, further diagnosis is required. Refer to the appropriate Chassis Diagnostic Manual or the service information available in the MDS2.
POLICY: Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
FAILURE CODE: