Instrument Panel Assembly

REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, SEAT BELT TENSIONER, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.

1. Remove the left A-pillar trim. A-Pillar Trim
2. Remove the top cover. Instrument Panel Top Cover
3. Disconnect the headliner harness electrical connector at the A-pillar.

Fig. 18 Instrument Panel Covers:

4. Using a trim stick C-4755 or equivalent, from the notch on the bottom, remove the left side cover. (Fig. 18)
5. Remove the steering column. Service and Repair

Fig. 5 Column Support:

6. Remove the two bolts at the column support bracket. (Fig. 5)
7. Remove the left cowl trim panel. Cowl Trim
8. Remove the instrument panel drivers side bezel. Instrument Panel Trim Bezel - Driver

Fig. 6 Left Side Mounting:

9. Remove the left side mounting bolts. (Fig. 6)

Fig. 7 Wire Harness Connectors:

10. Disconnect the wire harness electrical connectors above the brake pedal. (Fig. 7)
11. Loosen the screws and remove the hood release handle from the bracket.
12. Disconnect the park brake release handle actuator rod.
13. Remove the airbag control module trim cover, if equipped. (Fig. 18)
14. Remove the floor console, if equipped. Floor Console

Fig. 8 Center Mounting Bolts:

15. Remove the center bracket bolts. (Fig. 8)
16. Disconnect the airbag control module electrical connector.
17. Remove the right cowl trim cover. Cowl Trim

Fig. 9 Right Wire Harness Connection:

18. Disconnect the two electrical connectors. (Fig. 9)

Fig. 10 Antenna Connection:

19. Disconnect the radio antenna. (Fig. 10)

Fig. 11 HVAC Instrument Panel Mounting:

20. Remove the one HVAC screw. (Fig. 11)

Fig. 12 Passenger Side Mounting:

21. Using a trim stick C-4755 or equivalent, from the notch on the bottom, remove the right end cap. (Fig. 12)
22. Remove the right A-pillar trim. A-Pillar Trim
23. Remove the two right side mounting bolts on the A-pillar and one right mounting bolt on the cowl side panel. (Fig. 12)

Fig. 13 Upper Cowl Panel Bolts:

24. Remove the four top instrument panel screws. (Fig. 13)
25. Remove the two top instrument panel bolts and remove the instrument panel.

INSTALLATION
1. Position the instrument panel assembly in vehicle.

Fig. 14 Brake Release Rod:

2. Route the park brake release rod through the instrument panel. (Fig. 14)
3. Install the instrument panel onto the left side guide pin and the right side guide hook.
4. Install the left side mounting bolts and tighten to 12 N.m (9 ft. lbs.).
5. Install the instrument panel drivers side bezel. Instrument Panel Trim Bezel - Driver
6. Install the left cowl trim panel. Cowl Trim
7. Connect the headliner harness electrical connector at the A-pillar.
8. Install the left A-pillar trim. A-Pillar Trim
9. Position the left end cap and seat the attachment clips fully.
10. Install the right side mounting bolts on the A-pillar and one right mounting bolt on the cowl side panel and tighten to 12 N.m (9 ft. lbs.).
11. Install the right A-pillar trim panel. A-Pillar Trim
12. Position the right end cap and seat the attachment clips fully.
13. Install the one HVAC mounting screw.
14. Connect the radio antenna.
15. Connect the two electrical connectors at the right cowl panel.
16. Install the right cowl trim cover. Cowl Trim
17. Connect the airbag control module electrical connector.
18. Install the center bracket bolts and tighten to 12 N.m (9 ft. lbs.).
19. Install the floor console, if equipped. Floor Console
20. Install the airbag control module cover, if equipped.
21. Connect the park brake release handle actuator rod.
22. Install the hood release handle and tighten the screws.
23. Install the two bolts at the column support bracket and tighten to 14 N.m (10 ft. lbs.).
24. Install the steering column. Service and Repair
25. Connect the wire harness electrical connectors above the brake pedal.
26. Install the two top instrument panel bolts and tighten to 12 N.m (9 ft. lbs.).
27. Install the four top instrument panel screws.
28. Install the instrument panel top cover. Instrument Panel Top Cover