Service Procedure
1. For vehicles equipped with Remote Keyless Entry, connect the DRB III to the diagnostic connector located under the instrument panel near the steering column.2. For vehicles equipped with Remote Keyless Entry, retrieve the current settings for the Central Timer Module (CTM) programmable features using the DRB III, Record the settings for future use.
a. Select # 1 - DRB III STANDALONE on the DRB III, and then press ENTER.
b. Select # 4 - CUSTOMER PREFERENCES, and then press ENTER.
c. Select # 1 - 1998-2003 CUSTOMER PREFERENCES, and then press ENTER.
d. Select # 1 - RKE HORN CHIRP, and then press ENTER. Record the preference and then press PAGE BACK.
e. Select # 5- ROLLING DOOR LOCKS, and then press ENTER. Record the preference and then press PAGE BACK.
f. Select # 6 - RKE UNLOCK SEQUENCE, and then press ENTER. Record the preference and then press PAGE BACK.
g. Press PAGE BACK to exit.
3. Disconnect the negative battery cable.
NOTE:
To enhance customer satisfaction, remember to reset the clock when you have completed the service procedure.
4. Remove the driver's door sill trim.
5. Remove the lower left kick panel.
NOTE:
On Durango (DN) vehicles, there are two screws that attach the kick panel.
6. Disconnect the three (3) electrical connectors from the CTM (Figure 1).
7. Remove the three (3) CTM bolts (Figure 1).
8. Remove and discard the CTM.
9. Install the new CTM
10. Install the CTM bolts (Figure 1). Tighten the bolts to 21 in-lbs (2.4 N.m). Do NOT overtighten.
11. Connect the three (3) CTM electrical connectors (Figure 1).
12. Install the lower left kick panel. For DN vehicles, tighten the kick panel screws securely.
13. Install the driver's door sill trim.
14. Connect the negative battery cable.
15. For vehicles equipped with Remote Keyless Entry (RKE), set the Central Timer Module (CTM) programmable features using the DRB III as follows:
a. On the DRB III, select # 1 - DRB STANDALONE, and then press ENTER.
b. Select # 4 - CUSTOMER PREFERENCES, and then press ENTER.
c. Select # 1 - 1998-2003 CUSTOMER PREFERENCES, and then press ENTER.
d. Select # 3 - COUNTRY CODE, and then press ENTER.
e. Press ENTER again.
f. Select # 1 - UNITED STATES, and then press ENTER.
g. Press ENTER again and then press PAGE BACK to exit.
h. Select # 4 - ENABLE VTSS, and then press ENTER.
i. Press ENTER again.
j. Press YES to enable, then insert the key in the driver's door lock cylinder, turn the key to the lock position and hold it until the door locks cycle. Remove the key from the door, place it in the ignition, turn the key to the RUN position and then press ENTER on the DRB III.
k. Select # 1 - RKE HORN CHIRP, and then press ENTER.
l. Select ENABLE or DISABLE to match the recorded preference, and then press ENTER.
m. Press PAGE BACK.
n. Select # 2 - PROGRAM RKE, and then press ENTER.
o. Select # 1 - KEY FOB # 1, and then press ENTER.
p. While holding Key Fob # 1 in your hand, press ENTER on the DRB III.
q. Press BOTH the LOCK and UNLOCK buttons on the key fob until a chime is heard.
r. Press the UNLOCK button on the key fob.
IMPORTANT:
Steps p. through r. must be completed within five (5) seconds.
s. Repeat Steps o. through r. for Key Fob # 2.
IMPORTANT:
Each key fob must be reprogrammed or it will not work.
t. After the second fob is programmed, press PAGE BACK.
u. Select # 5 - ROLLING DOOR LOCKS, and then press ENTER.
v. Select ENABLE or DISABLE to match the recorded preference, and then press ENTER.
w. Press PAGE BACK.
x. Select # 6 - RKE UNLOCK SEQUENCE, and then press ENTER.
y. Select # 1- DRIVER FIRST or # 2 - ALL DOORS UNLOCK to match the recorded preference, and then press PAGE BACK.
z. Press PAGE BACK.
aa. Select # 7 - RADIO EQ SETTING, and then press ENTER.
bb. Select the appropriate body style, and then press ENTER.
cc. Press PAGE BACK.
dd. Verify that both key fobs operate properly.