System Overview
AIRBAG SYSTEM
The airbag system is designed to provide increased driver and passenger protection if the vehicle is involved in a front end collision. The system is most effective when used in conjuction with the seat belt system.
The Airbag Control Module (ACM) is an electronic module that monitors the airbag system for proper operation, stores diagnostic trouble code (DTC's), controls the airbag warning lamp and contains the sensor and actuator that is responsible for airbag deployment. There are no external impact sensors. The ACM is mounted on a special bracket that is fastened to the floor of the truck at the bottom of the instrument panel. It is located forward of the console. The ACM provides diagnostic information (DTC's) to the technician through the DRB III via the PCI bus. Some circuits are tested continously; others are checked only under certain circumstances. The warning lamp is driven with messages relayed to the Electro/Mechanical Instrument Cluster (EMIC) from the ACM via the PCI bus.
The AIRBAG warning lamp is the only point at which "symptoms" of a system malfunction can be observed by the customer. Whenever the ignition key is turned to the "run" position, the airbag control module performs a lamp check by turning the AIRBAG warning lamp ON for 6-8 seconds. If the lamp remains OFF, it means that the ACM has checked the system and found it to be free of discernible malfunctions. If the lamp remains ON, there could be an active fault in the system or the circuit that operates the lamp may be shorted to ground. If the lamp comes ON and stays ON for a period longer than 6-8 seconds, then goes OFF, there is usually an intermittent problem in the system.
WARNING: THE AIRBAG CONTROL MODULE CONTAINS THE IMPACT SENSOR, WHICH ENABLES THE SYSTEM TO DEPLOY THE AIRBAG. BEFORE ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIRBAG SYSTEM OR RELATED STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENTS YOU MUST FIRST DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE. THEN WAIT TWO MINUTES FOR THE SYSTEM CAPACITOR TO DISCHARGE BEFORE FURTHER SYSTEM SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE TO DO THIS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
NEVER STRIKE OR KICK THE AIRBAG CONTROL MODULE, AS IT CAN DAMAGE THE IMPACT SENSOR OR AFFECT ITS CALIBRATION. IF AN AIRBAG CONTROL MODULE IS ACCIDENTALLY DROPPED DURING SERVICE, THE MODULE MUST BE SCRAPPED AND REPLACED WITH A NEW UNIT.
Driver Airbag
The airbag protective trim cover is the most visible part of the driver side airbag system. The protective trim cover is fitted to the front of the airbag module and forms a decorative cover in the center of the steering wheel. The module is mounted directly to the steering wheel. Located under the trim cover are the horn switch, the airbag cushion, and the airbag cushion supporting components. The airbag module includes a housing to which the cushion and hybrid inflator are attached and sealed. The airbag module cannot be repaired, and must be replaced if deployed or in any way damaged.
Clockspring
The clockspring is mounted on the steering column behind the steering wheel. This assembly consist of a plastic housing which contains a flat, ribbon-like, electrically conductive tape that winds and unwinds with the steering wheel rotation. The clockspring is used to maintain a continuous electrical circuit between the instrument panel wiring and the driver airbag, the horn, and the vehicle speed control switches if equipped. The clockspring must be properly centered when it is reinstalled on the steering column following any service procedure, or it could be damaged. The clockspring cannot be repaired and it must be replaced.
Passenger Airbag
When supplied with the proper electrical signal the passenger airbag inflator or inflators discharge the gas directly into the cushion. The airbag module cannot be repaired, and must be replaced if deployed or in any way damaged.
WARNING: THE PASSENGER AIRBAG MODULE CONTAINS ARGON GAS PRESSURIZED TO 17236.89 Kpa (2500 PSI). DO NOT ATTEMPT TO DISMANTLE AN AIRBAG MODULE OR TAMPER WITH ITS INFLATOR. DO NOT PUNCTURE, INCINERATE, OR BRING INTO CONTACT WITH ELECTRICITY. DO NOT STORE AT TEMPERATURE EXCEEDING 93° C (200° F). REPLACE AIRBAG SYSTEM COMPONENTS ONLY WITH PARTS SPECIFIED IN THE MOPAR PARTS CATALOG. SUBSTITUTE PARTS MAY APPEAR INTERCHANGEABLE, BUT INTERNAL DIFFERENCES MAY RESULT IN INFERIOR OCCUPANT PROTECTION. THE FASTENERS, SCREWS, AND BOLTS ORIGINALLY USED FOR THE AIRBAG SYSTEM COMPONENTS HAVE SPECIAL COATINGS AND ARE SPECIFICALLY DESIGNED FOR THE AIRBAG SYSTEM. THEY MUST NEVER BE REPLACED WITH ANY SUBSTITUTES. ANY TIME A NEW FASTENER IS NEEDED, REPLACE IT WITH THE CORRECT FASTENERS PROVIDED IN THE SERVICE PACKAGE OR SPECIFIED IN THE MOPAR PARTS CATALOG.
Passenger Airbag ON-OFF Switch
The Passenger Airbag ON-OFF Switch allows the customer to turn the passenger airbag function ON or OFF. The OFF indicator will be illuminated whenever the switch is turned to the OFF position and for 2 seconds at ignition ON for an indicator bulb test. The switch assembly is mounted in the center of instrument panel to make the OFF indicator visible to all front seat occupants.
WARNING: ALWAYS CHECK THE PASSENGER AIRBAG ON-OFF SWITCH POSITION BEFORE DRIVING THE VEHICLE. A SWITCH IN THE WRONG POSITION INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A COLLISION.
To operate, insert the ignition key into the switch keyhole, push key in to release the internal plunger, and rotate to the desired switch position. The spring-loaded locking plunger prevents the user from leaving the key in the switch. The key will be automatically ejected when force is not applied. The ignition key is the only key or object that should ever be inserted into the switch.
NOTE: Do not turn the ON-OFF switch with the ignition ON.
The ACM continuously monitors the resistance of the Passenger Airbag ON-OFF Switch circuits to identify the switch position and provide circuit diagnostics. The ON-OFF switch ON position resistance is 175 to 190 ohms and the OFF position resistance is 820 to 870 ohms. If the ON-OFF switch circuits are open, shorted to ground or battery the ACM will set active and stored DTC. Upon receiving a switch diagnostic trouble code the airbag warning indicator, in the instrument cluster, will be turned ON by the ACM. Whenever the airbag warning indicator is illuminated, the ACM should be the first module interrogated.
WARNING: IGNORING THE AIRBAG WARNING LIGHT IN YOUR INSTRUMENT PANEL COULD MEAN THE PASSENGER AIRBAG ON-OFF SWITCH IS NOT FUNCTIONAL AND THE AIRBAG MAY DEPLOY IF AN IMPACT OCCURS. IF THE AIRBAG WARNING LIGHT TURNS ON WHILE DRIVING, THE AIRBAG ON-OFF SWITCH SETTING WILL REMAIN FUNCTIONAL FOR THAT KEY CYCLE. IF THE AIRBAG WARNING LIGHT COMES ON AGAIN AT THE NEXT KEY ON AND STAYS LIT FOR MORE THAN 6-8 SECONDS, THE ACM WILL DEFAULT TO PASSENGER AIRBAG ON.
Seat Belt Tensioner
Front seat belt systems incorporate Tensioner Modules (SBT). At the onset of an impact event each tensioner uses a pyrotechnic device, which is triggered simultaneously with the airbags, to rapidly retract the seat belts. With the slack removed, the occupant's forward motion in an impact will be reduced as will the likelihood of contacting interior components. After an impact that deploys the airbag, the seat belt tensioner assembly must be replaced.
The ACM module monitors the Seat Belt Tensioners circuit resistance and reports active and stored DTC's if any problem is found.
Side Impact Airbag Control Module (SIACM)
Supplemental driver and front passenger curtain airbags provide side impact protection for the front and rear seat occupants. Each curtain airbag has its own side impact airbag control module (SIACM) to provide independent impact sensing and deployment. SIACM are located on the left and right B post just below the seat belt retractor. The SIACM performs self diagnostics and circuit tests to determine if the system is functioning properly. If the test finds a problem the SIACM will set both active and stored diagnostic trouble codes. The results of the system test are transmitted on the PCI Bus to the ACM once each second. If the warning lamp status message from either SIACM contains a lamp ON request, the ACM will set an active DTC. At the same time as the DTC is set the ACM sends a PCI Bus message to the mechanical instrument cluster (MIC) requesting the airbag warning lamp be turned ON. Observe all ACM warning and caution statements when servicing or handling the SIACM. SIACM are not repairable and must be replaced if they are dropped.
WARNING: THE AIRBAG SYSTEM IS A SENSITIVE, COMPLEX ELECTROMECHANICAL UNIT. BEFORE ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIRBAG SYSTEM OR RELATED STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENTS YOU MUST FIRST DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE. WAIT TWO MINUTES FOR THE SYSTEM CAPACITOR TO DISCHARGE BEFORE FURTHER SYSTEM SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE TO DO THIS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY. NEVER STRIKE OR KICK THE AIRBAG CONTROL MODULE, AS IT CAN DAMAGE THE IMPACT SENSOR OR AFFECT ITS CALIBRATION. IF AN AIRBAG CONTROL MODULE IS ACCIDENTALLY DROPPED DURING SERVICE, THE MODULE MUST BE SCRAPPED AND REPLACED WITH A NEW UNIT.
Curtain Airbags
The Left and Right curtain airbags are located in the outboard edge of the roof under the headliner, just above the door openings. When supplied with the proper electrical signal the inflator can discharge the compress gas directly into the curtain airbag. Upon deployment, the curtain will tear open the headliner allowing the curtain airbag to fully deploy between the headliner and seat. The curtain airbag cannot be repaired and must be replaced if deployed or in any way damaged.
WARNING: THE CURTAIN AIRBAG CONTAINS AN INERT GAS PRESSURIZED TO 17236.89 Kpa (2500 PSI). DO NOT ATTEMPT TO DISMANTLE AN AIRBAG MODULE OR TAMPER WITH ITS INFLATOR. DO NOT PUNCTURE, INCINERATE, OR BRING INTO CONTACT WITH ELECTRICITY. DO NOT STORE AT TEMPERATURE EXCEEDING 93 ° C (200 ° F). REPLACE AIRBAG SYSTEM COMPONENTS ONLY WITH PARTS SPECIFIED IN THE CHRYSLER MOPAR PARTS CATALOG. SUBSTITUTE PARTS MAY APPEAR INTERCHANGEABLE, BUT INTERNAL DIFFERENCES MAY RESULT IN INFERIOR OCCUPANT PROTECTION. THE FASTENERS, SCREWS, AND BOLTS ORIGINALLY USED FOR THE AIRBAG SYSTEM COMPONENTS HAVE SPECIAL COATINGS AND ARE SPECIFICALLY DESIGNED FOR THE AIRBAG SYSTEM. THEY MUST NEVER BE REPLACED WITH ANY SUBSTITUTES. ANY TIME A NEW FASTENER IS NEEDED, REPLACE IT WITH THE CORRECT FASTENERS PROVIDED IN THE SERVICE PACKAGE OR SPECIFIED IN THE MOPAR PARTS CATALOG.