Vehicles Using DRBIII(R)

NOTE:
Whenever a controller is programmed, the software in the DRBIII(R); must be programmed with the latest revision level available.

NOTE:
If this flash process is interrupted/aborted, the flash should be restarted and then follow the directions on the DRBIII(R).

1. Before beginning the reprogramming procedure, remove any old flash reprogramming files from the DRBIII(R) memory. To clear the memory from the MAIN MENU:

a. Simultaneously press the "MORE" and "YES" keys.

b. A screen will appear requesting a "COLD BOOT".

c. Follow the on screen instructions by selecting the "F4" key.

d. When the DRBIII(R) reboots to the MAIN MENU, proceed to Step # 2

2. With the ignition switch in the "RUN" position, determine the original part number of the PCM currently in the vehicle. Using the DRBIII(R) select:

a. "DRBIII(R) Standalone"

b. "1998 - 20045 Diagnostics"

c. "All (Except Below)"

d. "Engine"

e. "Module Display"

f. Record the "PCM part # " on the repair order for later reference.

3. Connect the DRBIII(R) to TechCONNECT. Open TechTOOLS and verify that the "DRBIII(R) Status: Connected" message is in the upper right corner of the TechTOOLS screen.

4. Enter the "PCM part # " recorded in Step #2 in the "Parts Criteria" area and select "Show Updates". TechTOOLS will populate the available updates.

5. Select the calibration.

6. Select the "DRBIII" radio button which is next to the "Download/Update" button.

7. Select the "Download/Update" button.

8. Monitor the "Flash Download/Update Progress" window on the TechCONNECT and follow the instructions on TechCONNECT. When the flash process is complete, proceed to Step # 9.

9. Disconnect the DRBIII(R) from TechCONNECT.

10. Open the hood, install a battery charger and verify that charging rate provides approximately 13.5 volts.

11. If the vehicle is a 2003 or later AN or 2002 or later DN or DR model, proceed to Step # 12. If not proceed Step # 15.

12. Using the DRBIII(R), determine the pinion factor stored in the Controller Anti-lock Brakes (CAB) and record it on the work order for later reference.

13. Turn the ignition switch to the "Off" position.

14. Disconnect the CAB module electrical connectors. Proceed to Step # 15.

15. Connect the DRBIII(R) to the vehicle.

16. Turn the ignition to the "Run" position (engine not running).

17. Download the flash from the DRBIII(R) to the vehicle. Using the DRBIII(R) select:

a. "Vehicle Flash"

b. Follow the directions on the DRBIII(R) screen. When the flash process is complete, proceed to Step # 18.

18. If the vehicle is a 2003 and later AN or 2002 or later DN or DR model, proceed to Step # 19. If not proceed to Step # 23.

19. Turn the ignition to the "Off" position.

20. Connect the CAB electrical connectors.

21. Turn the ignition switch to the "Run" position (engine not running).

22. Using the DRBIII(R), check the pinion factor in the CAB to be sure that it was not erased during the flash process. If the pinion factor is not present or is not correct, enter the correct pinion factor. Proceed to Step # 23.

NOTE:
Due to the PCM programming procedure, a DTC may be set in other modules. (TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate. From the "Home" Screen select "System View". Then select "All DTCs". Press "Clear All Stored DTCs" if there are any DTCs shown on the list.

NOTE:
The following step is required by law.





23. Type the necessary information on the "Authorized Modification Label" p/n 04275086AB and attach near the VECI label (Fig. 1).