Engine No Start/Hard Start
*ENGINE NO START/HARD START
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.
Diagnostic Test
1. DTC/PRODUCT IMPROVEMENT
Check for any TSB's related to customer's complaint or DTC's present.
Follow appropriate guidelines in DTC troubleshooting tree or instructions in TSB.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 2
2. BATTERY VOLTAGE
Check for low battery voltage.
Is battery voltage okay?
No
- Repair low battery voltage.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
Yes
- Go To 3
3. STARTING ACCESSORIES
Inspect the Ignition switch (check for proper output voltage and/or open circuit).
Inspect the Starter.
Inspect the Grid Heaters.
Inspect the Fuel Heater.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 4
4. ENGINE TIMING
Inspect speed indicator ring for damaged/missing teeth.
Inspect for dirty or damaged pins at Crankshaft position sensor (CKP) or Camshaft position sensor (CMP).
Verify proper overhead adjustments.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 5
5. FUEL SUPPLY SYSTEM
Verify proper fuel quality, grade and level in vehicle.
Use scan tool to monitor fuel rail pressure. If pressure does not fluctuate more then ± 500 psi of setpoint than the fuel system is not the cause of the complaint. Proceed to step 6. If condition exist continue.
Verify proper low pressure supply to the Injection Pump by performing the "*IN-TANK FUEL LIFT PUMP FLOW TEST - DIESEL" Procedure. In-Tank Fuel Lift Pump Flow/Diagnostic Test Procedure
Use the "*HIGH PRESSURE FUEL PUMP PERFORMANCE TEST - DIESEL" to check for failed fuel pump.
Perform "*CHECKING PRESSURE LIMITING VALVE ON THE FUEL - DIESEL". Pressure Limiting Valve Test
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 6
6. INJECTION SYSTEM
Perform "*INJECTOR RETURN FLOW TEST". Injector Return Flow Test
If okay go next step.
Check for correct injectors and injector shims.
Visually inspect injector wire nuts and pass through connectors for damage or corrosion.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 7
7. FUEL RETURN
Check for kinked or restricted fuel return lines.
Check fuel tank venting.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 8
8. INTAKE SYSTEM
Check for inlet restriction, inspect air filter for excessive dirt/debris. Verify air intake lines are not kinked or restricted.
Check for air system leaks. Perform "*INTAKE AIR SYSTEM PRESSURE TEST - DIESEL". Intake Air System Pressure Test
Inspect Turbocharger for wheel clearance and proper wastegate operation.
Check for exhaust restriction. Verify proper exhaust brake operation. Check for kinked or blocked exhaust pipes.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 9
9. OTHER VEHICLE SYSTEMS
Verify proper operation of the Transmission Clutch.
Verify proper operation of the Transmission.
Verify proper operation of the Vehicle brakes (check for dragging).
Verify proper operation of the Cooling fan operation cycle time.
Verify proper operation of the Engine driven accessories.
Verify proper operation of the Accelerator pedal (restricted or out of calibration).
Verify no excess Electrical Noise.
Verify no Moisture in harness connector or corroded terminals.
Is vehicle repaired?
Yes
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test
No
- Go To 10
10. BASE ENGINE
Inspect speed indicator ring for damaged/missing teeth.
Check for internal engine damage.
Repair Complete.
Repair
- Repair complete.
- Perform POWERTRAIN VERIFICATION TEST. Powertrain Verification Test