P0112

P0112-INTAKE AIR TEMPERATURE SENSOR CIRCUIT LOW





For a complete wiring diagram, refer to the Wiring Information Electrical Diagrams.

- When Monitored:
With the ignition on and battery voltage greater than 10.4 Volts.

- Set Condition:
When the Intake Air Temperature (IAT) sensor signal circuit voltage is less than the minimum acceptable voltage. One trip failure. Three good trips to clear the Malfunction Indicator Lamp (MIL).





WARNING: On vehicles equipped with the high voltage system, you must thoroughly read and follow all High Voltage Safety procedures. In addition, before performing any diagnostic or service procedure near a high voltage component, you must perform the High Voltage Power Down. Failure to follow these instructions may result in possible serious or fatal injury

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.Pre-Diagnostic Troubleshooting Procedure.

1. ACTIVE DTC
1. Start the engine and allow it to reach normal operating temperature.

WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.

NOTE: Diagnose and repair any system voltage DTCs before continuing with this test.

2. With the scan tool, select View DTCs.

Is the DTC active at this time?

Yes

- Go To 2

No

- Refer to the INTERMITTENT CONDITION Diagnostic Procedure. Intermittent Condition Test.

2. IAT SENSOR
1. Turn the ignition off.
2. Disconnect the IAT sensor harness connector.
3. Ignition on, engine not running.
4. With the scan tool, read IAT voltage.

NOTE: The sensor voltage should be approximately 5.0 Volts (+/- 0.1 Volts) with the connector disconnected.

Does the scan tool display the voltage as described above?

Yes

- Verify that there is good pin to terminal contact in the IAT sensor and PCM connectors. Replace the IAT sensor if no problems were found in the connectors.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Go To 3

3. (K21) IAT SENSOR SIGNAL SHORTED TO GROUND




1. Turn the ignition off.
2. Disconnect the C2 PCM harness connector.
3. Measure the resistance between ground and the (K21) IAT signal circuit in the IAT sensor harness connector.

Is the resistance below 100 Ohms?

Yes

- Repair the short to ground in the (K21) IAT signal circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Go To 4

4. (K21) IAT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT




1. Measure the resistance between the (K21) IAT signal circuit and the (K900) sensor ground circuit in the IAT sensor harness connector.

Is the resistance below 100 Ohms?

Yes

- Repair the short between the (K900) sensor ground circuit and the (K21) IAT signal circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Go To 5

5. EXCESSIVE RESISTANCE IN THE (K21) IAT SIGNAL CIRCUIT





CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals, resulting in poor terminal to pin connection. Install PCM Pinout Box 8815 to perform diagnosis.

1. Measure the resistance of the (K21) IAT signal circuit between the IAT sensor harness connector and the appropriate terminal of special tool #8815.

Is the resistance below 5.0 Ohms?

Yes

- Go To 6

No

- Repair the excessive resistance in the (K21) IAT signal circuit.
- Perform the POWERTRAIN VERIFICATION TEST.Powertrain Verification Test.

6. POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and electrical connectors between the IAT sensor and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the IAT sensor and PCM connectors.
4. Search for any Technical Service Bulletins (TSBs) that may apply.

Were there any problems found?

Yes

- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Replace and program the PCM in accordance with the Service Information.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.