B121A
B121A-RIGHT HEATED SEAT HI INDICATOR CONTROL CIRCUIT HIGH
For a complete wiring diagram, refer to the Wiring Information Electrical Diagrams.
- When Monitored:
Continuously with the ignition on.
- Set Condition:
When the Cluster detects no Voltage on the (P84) Passenger Heated Seat High Indicator Driver circuit.
1. VERIFY DIAGNOSTIC TROUBLE CODE (DTC) B121A-RIGHT HEATED SEAT HI INDICATOR CONTROL CIRCUIT HIGH IS ACTIVE
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
3. Operate the Heated Seat Switch in both positions several times.
4. With the scan tool, read DTCs.
Is DTC B121A-RIGHT HEATED SEAT HI INDICATOR CONTROL CIRCUIT HIGH active
Yes
- Go To 2
No
- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
2. INSPECT JB FUSE #19
1. Inspect JB Fuse #19.
Is the fuse open?
Yes
- Using the wiring diagram/schematic as a guide, inspect wiring, connectors, and components for the cause of the open fuse, and repair as necessary.
- Replace JB Fuse #19.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Go To 3
3. CHECK (P84) PASSENGER HEATED SEAT HIGH INDICATOR DRIVER CIRCUIT VOLTAGE AT CLUSTER
1. Turn the ignition off.
2. Reinstall JB Fuse #19 if removed in previous step.
3. Disconnect the Cluster C3 connector.
NOTE: Check connectors - Clean and repair as necessary.
4. Turn the ignition on.
5. Measure the voltage at the (P84) Passenger Heated Seat High Indicator Driver circuit between the Cluster C3 connector and ground.
Is the voltage above 10.0 volts?
Yes
- Replace the Cluster.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Go To 4
4. CHECK (F21) FUSED IGNITION SWITCH OUTPUT (RUN-START) CIRCUIT VOLTAGE AT PASSENGER HEATED SEAT SWITCH
1. Turn the ignition off.
2. Disconnect the Passenger Heated Seat Switch connector.
NOTE: Check connectors - Clean and repair as necessary.
3. Turn the ignition on.
4. Measure the voltage of the (F21) Fused Ignition Switch Output (Run-Start) circuit between the Passenger Heated Seat Switch connector and ground.
Is the voltage above 10.0 volts?
Yes
- Go To 5
No
- Repair the (F21) Fused Ignition Switch Output (Run-Start) circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
5. CHECK (P84) PASSENGER HEATED SEAT HIGH INDICATOR DRIVER CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Measure the resistance of the (P84) Passenger Heated Seat High Indicator Driver circuit between ground and the Passenger Heated Seat Switch connector.
Is the resistance below 10K Ohms?
Yes
- Repair the (P84) Passenger Heated Seat High Indicator Driver circuit for a short to ground.NOTE: The short may have damaged the Passenger Heated Seat switch. Go To 8 to test the switch.
No
- Go To 6
6. CHECK (P84) PASSENGER HEATED SEAT HIGH INDICATOR DRIVER CIRCUIT FOR A SHORT TO (Z978) GROUND CIRCUIT
1. Measure the resistance between the (P84) Passenger Heated Seat High Indicator Driver circuit and the (Z978) Ground circuit at the Passenger Heated Seat Switch connector.
Is the resistance below 10K Ohms?
Yes
- Repair the (P84) Passenger Heated Seat High Indicator Driver circuit for a short to the (Z978) Ground circuit.NOTE: The short may have damaged the Passenger Heated Seat switch. Go To 8 to test the switch.
No
- Go To 7
7. CHECK (P84) PASSENGER HEATED SEAT HIGH INDICATOR DRIVER CIRCUIT FOR AN OPEN
1. Measure the resistance of the (P84) Passenger Heated Seat High Indicator Driver circuit between the Passenger Heated Seat Switch connector and the Cluster C3 connector.
Is the resistance below 5.0 Ohms?
Yes
- Replace the Passenger Heated Seat Switch.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Repair the (P84) Passenger Heated Seat High Indicator Driver circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
8. CHECK FOR OPEN PASSENGER HEATED SEAT SWITCH
1. Reconnect the Cluster C3 connector.
2. Reconnect the Passenger Heated Seat Switch connector.
3. Turn the ignition on.
4. Measure the voltage of the (P84) Passenger Heated Seat High Indicator Driver circuit between the Passenger Heated Seat Switch connector and ground.
Is the voltage above 10.0 volts?
Yes
- Test Complete. Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Replace the Passenger Heated Seat Switch.
- Perform the BODY VERIFICATION TEST. Body Verification Test.