Engine - Removal

REMOVAL





1. Perform fuel pressure release procedure Service and Repair.
2. Disconnect negative battery cable (3).
3. Remove air cleaner and hoses.





4. Disconnect the fuel line (1) from fuel rail Service and Repair.
5. Remove the wiper module Wiper Arm Linkage - Removal.





6. Block off heater hoses to the rear heater system using pinch-off pliers (if equipped).
7. Drain the cooling system Service and Repair.
8. Disconnect the heater hoses.
9. Remove the radiator upper support crossmember (2) Radiator Crossmember - Removal.





10. Remove the radiator fans Cooling Fan - Removal.
11. Disconnect the ETC connector (3) from the throttle body.
12. Disconnect the MAP, IAC, and TPS electrical connectors.
13. Disconnect the EGR transducer electrical connector (if equipped).
14. Disconnect the vacuum hoses from throttle body.





15. Disconnect the brake booster and speed control vacuum hoses.
16. Disengage wire harness clip from the right side engine mount.
17. Remove the power steering reservoir (2) from mounting position and set aside.
18. Disconnect ground strap from rear of cylinder head.





19. Disconnect engine coolant temperature (ECT) sensor and ignition coil electrical connectors.
20. Disconnect the fuel injector electrical harness connector and disengage clip from support bracket.
21. Disconnect camshaft and crankshaft (2) position sensor electrical connectors.





22. Evacuate air conditioning system.
23. Disconnect A/C compressor electrical connector.
24. Disconnect the A/C lines (2,5) from compressor. Cover and seal all openings of hoses and compressor.
25. Remove the radiator upper hose.
26. Disengage electrical harness clip at transaxle dipstick tube.
27. Remove transaxle dipstick tube. Seal opening using a suitable plug.
28. Remove transaxle cooler lines
29. Disconnect transaxle shift linkage and electrical connectors.





30. Raise vehicle on hoist and drain the engine oil.
31. Remove the axle shafts. Half Shaft - Removal.
32. Remove the fore/aft crossmember (5).









33. Disconnect exhaust pipe (4) from the manifold.

34. Remove front engine mount bracket.
35. Remove the engine rear mount bracket.
36. Remove transaxle case cover.
37. Remove flex plate to torque converter bolts. Mark torque converter to flex plate for orientation for reassembly.
38. Remove the power steering pressure hose support clip attaching bolt.
39. Disconnect the knock sensor electrical connector (3.8L only).
40. Disconnect the engine block heater electrical connector (if equipped).
41. Remove the accessory belt splash shield.
42. Remove accessory drive belt Serpentine Accessory Drive Belt - Removal.
43. Disconnect the radiator lower hose.
44. Remove air conditioning compressor from engine.
45. Remove the generator Generator - Removal.
46. Remove the water pump pulley attaching bolts and position pulley between pump hub and housing.
47. Disconnect the oil pressure switch electrical connector.
48. Disconnect wiring harness support clip from engine oil dipstick tube.
49. Install Special Tools 6912 and 8444 Adapters on the right side (rear) of engine block.









50. Lower the vehicle.
51. Remove the power steering pump and set aside.
52. Raise vehicle enough to allow engine dolly Special Tool 6135 and cradle Special Tool 6710A with post Special Tool 6848 and adaptor Special Tool 6909A to be installed under vehicle.
53. Loosen cradle/post mounts to allow movement for positioning posts into locating holes on the engine and. Slowly lower vehicle and position cradle/post mounts until the engine is resting on posts. Tighten all cradle/post mounts to cradle frame. This will keep mounts from moving when removing or installing engine and transmission.


















54. Lower vehicle so the weight of ONLY THE ENGINE AND TRANSMISSION is on the cradle.
55. Install and secure the safety straps to the cradle fixture and around the engine.
56. Remove the engine right side mount to engine attaching bolts.
57. Remove the left mount through bolt.
58. Raise vehicle slowly. It is necessary to move the engine/transmission assembly with the dolly to allow for removal around body flanges.