P0452
P0452-EVAP PRESSURE SWITCH STUCK CLOSED
For a complete wiring diagram, refer to the Wiring Information.
- When Monitored:
Immediately after the ignition has been turned off.
- Set Condition:
At key off, the Powertrain Control Module (PCM) energizes the Purge Solenoid for a calibrated amount of time (30 seconds maximum) and stores the state of the Evaporative System Integrity Monitor (ESIM) switch. The state is evaluated again at the next key on. If the PCM does not detect that the ESIM Switch is open, an error is detected. Two Trip Fault. Three good trips to turn off the MIL.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Pre-Diagnostic Troubleshooting Procedure.
1. VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
1. Ignition on, engine not running.
2. With the scan tool, select View DTCs and record the related Freeze Frame data if any DTCs are present.
3. Whether or not any DTCs are Active you will want to check the following items which may assist in repairing the customer's complaint successfully.
4. Check the vehicle's repair history.
5. If the vehicle has a repair history that pertains to the customer's current complaint, review the repair.
6. Inspect the vehicle for any aftermarket accessories that may have been installed incorrectly.
7. Check for any service bulletin(s) related to the customer's complaint or DTCs.
8. If a service bulletin applies, follow the instructions per the service bulletin.
Choose the following scenario that best applies.
The service bulletin repaired the customer's complaint.
- Testing complete.
A DTC is present, no service bulletins apply or the service bulletin didn't repair the customer's complaint.
- Go To 2
2. ACTIVE DTC
NOTE: If the customer is experiencing an early fuel shut off during the fuel filling process along with P0440, P0441 and P0452 setting, you need to check for restrictions in the Evap Purge tubes/hoses as well as the Fresh Air Filter before continuing.
1. Start the engine.
2. Allow the engine to reach normal operating temperature.
3. With the scan tool, select View DTCs and record the related Freeze Frame data.
4. It may be necessary to drive the vehicle to meet the conditions to set this DTC, try to repeat the conditions in which the fault originally set by reviewing the Freeze Frame data.
Is the DTC Active or Pending at this time?
Yes
- Go To 3
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. . Intermittent Condition Test
3. ESIM SWITCH STATE
1. With the scan tool, select Data Display and view the ESIM Switch state.
2. Disconnect the purge hose from the Evap canister.
Is the ESIM Switch state change from 'Closed' to 'Open' when the purge hose was disconnected?
Yes
- Go To 4
No
- Go To 7
4. EVAP PURGE HOSE/TUBE AND FRESH AIR FILTER OBSTRUCTION
1. Turn the ignition off.
2. Inspect the Evap Purge hose/tube for proper routing and installation between the Evap Purge Solenoid and the Fuel Tank and between the Fuel Tank and the Evap Purge Canister.
3. Make sure the hose/tube and fresh air filter are not damaged, kinked and free from any obstructions.
4. Check for any kinks in the purge line connecting the Evap Purge valve to intake manifold.
Were any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Go To 5
5. (K52) EVAP PURGE CONTROL CIRCUIT SHORTED TO GROUND
1. Disconnect the C3 PCM harness connector.
2. Measure the resistance between ground and the (K52) Evap Purge Control circuit in the Evap Purge Solenoid harness connector.
Is the resistance below 100 Ohms?
Yes
- Repair the short to ground in the (K52) Evap Purge Control circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Go To 6
6. EVAP PURGE SOLENOID
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Evap Purge Solenoid and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Verify that there is good pin to terminal contact in the Evap Purge Solenoid and the Powertrain Control Module connectors.
5. Perform any Technical Service Bulletins that may apply.
Were any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Replace the Evap Purge Solenoid.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
7. ESIM ASSEMBLY
1. With the scan tool, select Data Display and view the ESIM Switch state.
2. Disconnect the ESIM switch electrical connector.
Does the ESIM switch state change from CLOSED to OPEN when the switch is disconnected?
Yes
- Verify that there is good pin to terminal contact in the ESIM and the Powertrain Control Module connectors. If OK, replace the ESIM Switch.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Go To 8
8. (K107) ESIM SIGNAL CIRCUIT SHORTED TO GROUND
1. Turn the ignition off.
2. Disconnect the C3 PCM harness connector.
3. Measure the resistance between ground and the (K107) ESIM signal circuit in the ESIM switch harness connector.
Is the resistance below 100 Ohms?
Yes
- Repair the short to ground in the (K107) ESIM signal circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Go To 9
9. POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Evap Purge Solenoid Assembly, ESIM Switch and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the ESIM, Evap Purge Solenoid and the Powertrain Control Module connectors.
4. Perform any Technical Service Bulletins that may apply.
Were there any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Replace and program the Powertrain Control Module.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.