Operation CHARM: Car repair manuals for everyone.
Home >> Dodge or Ram Truck >> 2010 >> Journey FWD L4-2.4L >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0014

P0014






P0014-BANK 1 CAMSHAFT 2 POSITION TARGET PERFORMANCE







- When Monitored:
Variable Valve Timing (VVT) rationality is monitored under the following conditions: (1) Cam phasing is commanded off of the default (lockpin) position; (2) Oil temperature is between -12° C to 139° C (10° F to 282° F); (3) Battery voltage is greater than 10 volts; (3) Engine speed is at least 650 to 1400 rpm, depending on oil temperature; (4) No CMP sensor, CKP sensor, or OBDI plausibility errors. Before VVT can be enabled, reference adaptation must be completed.

- Set Condition:
The actual camshaft phasing position is not moving towards the desired camshaft phasing position during steady state operation.





Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding Pre-Diagnostic Troubleshooting Procedure.

Theory of Operation

Dual Variable Valve Timing (VVT) allows the PCM to monitor and adjust the position of each camshaft, based on desired torque levels and engine operating conditions. The PCM controls two solenoid operated control valves, one for each camshaft, that are used to direct oil pressure to hydraulic actuators mounted between each camshaft and its driving sprocket. The oil pressure alters the angular position or phasing of each camshaft relative to crankshaft rotation. A sensor is used to monitor the position of each camshaft.

1. DTC IS ACTIVE

NOTE: Diagnose and repair any system voltage DTCs before continuing with this test.

NOTE: Diagnose and repair any CMP sensor or CKP sensor DTCs before continuing with this test.

NOTE: Diagnose and repair any oil pressure or oil pressure sensor DTCs before continuing with this test.

1. Start the engine and allow it to reach normal operating temperature.

WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.

2. With the scan tool, Clear DTCs in the Powertrain Control Module (PCM).
3. Test drive the vehicle under the conditions in which the DTC is monitored, as outlined above.
4. With the scan tool, select View DTCs.

Is the status Active for this DTC?

Yes

- Go to 2

No

- Perform the CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure Checking for an Intermittent DTC.

2. VVT EXHAUST SOLENOID INSPECTION
1. Turn the ignition off.
2. Remove the VVT Exhaust Solenoid. Do not disconnect the harness connector.
3. Perform a visual inspection of the open part of the VVT Exhaust Solenoid (spool valve) for the presence of any debris (metallic or non-metallic).

NOTE: If contamination is observed, the VVT Exhaust Solenoid must be replaced. After replacing the valve, verify that the engine oil has been replaced with the appropriate oil.

Were any problems found?

Yes

- Replace the VVT Exhaust Solenoid.
- Perform the PCM Verification Test PCM Verification Test.

No

- Go to 3

3. VVT EXHAUST SOLENOID ACTUATION
1. Turn the ignition on.
2. With the scan tool, actuate the VVT Exhaust Solenoid.
3. Perform a visual inspection of the spool valve for erratic movement or sticking during the forward and reverse stroke.

NOTE: If sticking or erratic movement is observed, the VVT Exhaust Solenoid must be replaced. After replacing the valve, verify that the engine oil has been replaced with the appropriate oil.

Select the appropriate response from the choices below:

Normal operation. No sticking or erratic movement is observed

- Go to 4

No movement is observed

- Go to 6

Sticking or erratic movement is observed

- Replace the VVT Exhaust Solenoid.
- Perform the PCM Verification Test PCM Verification Test.

4. INCORRECT ENGINE OIL VISCOSITY
1. Review the vehicle service history to determine if the correct viscosity engine oil was used.

Were any problems found?

Yes

- Change the engine oil and filter and retest.
- Perform the PCM Verification Test PCM Verification Test.

No

- Go to 5

5. ENGINE OIL DIRTY OR CONTAMINATED
1. Turn the ignition off.
2. Inspect engine oil for signs of contamination, sludge, or foreign material.

Were any problems found?

Yes

- Clean the engine of oil sludge. Once the engine is cleaned of excessive sludge, replace oil and oil filter.
- Perform the PCM Verification Test PCM Verification Test.

No

- Go to 11

6. VVT EXHAUST SOLENOID WIRING AND CONNECTORS
1. Turn the ignition off.
2. Inspect the wiring and connectors between the VVT Exhaust Solenoid and the Powertrain Control Module (PCM).
3. Look for any chafed, pierced, pinched, or partially broken wires.
4. Look for broken, bent, pushed out or corroded terminals.

Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test PCM Verification Test.

No

- Go to 7

7. (F344) FUSED ASD/MAIN RELAY OUTPUT CIRCUIT HIGH RESISTANCE




1. Turn the ignition off.
2. Disconnect the VVT Exhaust Solenoid connector.
3. Turn the ignition on.
4. Using a 12 volt test light connected to ground, check the (F344) Fused ASD/Main Relay Output circuit in the VVT Exhaust Solenoid harness connector.

NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.

Is the test light illuminated and bright?

Yes

- Go to 8

No

- Repair the (F344) Fused ASD/Main Relay Output circuit for high resistance.
- Perform the PCM Verification Test PCM Verification Test.

8. (K276) VVT EXHAUST CONTROL CIRCUIT ACTUATION




1. With the scan tool, actuate the VVT Exhaust Solenoid to the ON (maximum) position.
2. Using a 12 volt test light connected to 12 volts, check the (K276) VVT Exhaust Control circuit in the VVT Exhaust Solenoid harness connector.

NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.

Is the test light illuminated and bright?

Yes

- Go to 10

No

- Go to 9

9. (K276) VVT EXHAUST CONTROL CIRCUIT OPEN OR HIGH RESISTANCE




1. Turn the ignition off.
2. Disconnect the Powertrain Control Module (PCM).

NOTE: When checking circuits at the Powertrain Control Module (PCM), be careful not to damage or distort the connector terminals. Improper measurement technique could result in poor pin to terminal contact.

3. Measure the resistance of the (K276) VVT Exhaust Control circuit between the VVT Exhaust Solenoid harness connector and the Powertrain Control Module (PCM) harness connector.

Is the resistance below 5.0 ohms?

Yes

- Go to 12

No

- Repair the (K276) VVT Exhaust Control circuit for an open circuit or high resistance.
- Perform the PCM Verification Test PCM Verification Test.

10. VVT EXHAUST SOLENOID
1. Turn the ignition off.
2. Inspect the wiring and connectors between the VVT Exhaust Solenoid and the Powertrain Control Module (PCM).
3. Look for any chafed, pierced, pinched, or partially broken wires.
4. Look for broken, bent, pushed out or corroded terminals.

Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test PCM Verification Test.

No

- Replace the VVT Exhaust Solenoid.
- Perform the PCM Verification Test PCM Verification Test.

11. CAMSHAFT PHASER
1. Turn the ignition off.
2. Remove the appropriate Camshaft Phaser.
3. Inspect the Phaser for contamination, foreign material, or any condition that would restrict operation of the Phaser.
4. Inspect the Phaser oil passages for signs of sludge or foreign material.

NOTE: The Phaser should not be disassembled. If the Phaser is damaged, it must be replaced.

Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test PCM Verification Test.

No

- Perform the CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. Checking for an Intermittent DTC.

12. POWERTRAIN CONTROL MODULE (PCM)
1. Turn the ignition off.
2. Inspect the wiring and connectors between the VVT Exhaust Solenoid and the Powertrain Control Module (PCM).
3. Look for any chafed, pierced, pinched, or partially broken wires.
4. Look for broken, bent, pushed out or corroded terminals.
5. Refer to any TSBs that apply.

Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test PCM Verification Test.

No

- Replace and program the Powertrain Control Module.
- Perform the PCM Verification Test PCM Verification Test.

pro multis · About Operation CHARM