B1B07
B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER
- When Monitored:
With the ignition on.
- Set Condition:
The Occupant Restraint Controller (ORC) monitors the resistance of the Driver Squib 2 circuits. The ORC will set this DTC if it detects low resistance between the Driver Squib 2 circuits.
1. DETERMINE ACTIVE OR STORED DTC
NOTE: Make sure that the battery is fully charged.
NOTE: The scan tool, SRS Load Tool Kit 8443A and DVOM are required to perform the following test.
1. Turn the ignition on.
Does the scan tool display B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER DTC?
Yes
- Go To 2
No
- Perform the AIRBAG SYSTEM INTERMITTENT TEST. Airbag System Intermittent Condition Test.
2. CHECK FOR SHORTED SQUIB CIRCUITS IN DRIVER AIRBAG
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
WARNING: Do not place an intact non-deployed airbag face down on a hard surface, the airbag propels into the air if accidentally deployed. Failure to follow these instructions may result in possible serious or fatal injury.
1. Disconnect the Driver Airbag Squib connectors.
NOTE: Check the connectors - Clean and repair as necessary.
2. Connect the SRS Load Tool Kit 8443A and SRS Load Tool Jumper 8443-1 or 8443-8 to the Driver Airbag Squib connectors.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
3. With the scan tool, read the active ORC DTCs.
Does the scan tool display B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER DTC?
Yes
- Go To 3
No
- Replace the Driver Airbag.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.
3. CHECK CLOCKSPRING SQUIB CIRCUITS FOR A SHORT TOGETHER
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Disconnect the SRS Load Tool Kit 8443A and Jumper from the Driver Airbag Squib connectors.
2. Disconnect the Clockspring C4 harness connector.
NOTE: Check the connectors - Clean and repair as necessary.
3. Connect the SRS Load Tool Kit 8443A and SRS Load Tool Jumper 8443-19 to the Clockspring C4 harness connector.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
4. With the scan tool, read the active ORC DTCs.
Does the scan tool display B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER DTC?
Yes
- Go To 4
No
- Replace the Clockspring.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.
4. CHECK (R63) DRIVER SQUIB 2 LINE 1 CIRCUIT FOR A SHORT TO THE (R61) DRIVER SQUIB 2 LINE 2 CIRCUIT
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Disconnect the SRS Load Tool Kit 8443A and Jumper from the Clockspring connector.
2. Disconnect the ORC connectors.
NOTE: Check the connectors - Clean and repair as necessary.
3. Connect the SRS Load Tool Adapter 8443-25 to the ORC connectors.
4. Measure the resistance between the (R63) Driver Squib 2 Line 1 circuit cavity 1 and the (R61) Driver Squib 2 Line 2 circuit cavity 2 in the Clockspring C4 connector.
Is the resistance below 10k Ohms?
Yes
- Repair the (R63) Driver Squib 2 Line 1 circuit for a short to the (R61) Driver Squib 2 Line 2 circuit.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.
No
- WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
- Replace the ORC.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.