B1E6A-15
B1E6A-15-PASSENGER MIRROR FOLD CONTROL CIRCUIT SHORT TO BATTERY OR OPEN
For a complete wiring diagram, refer to the Wiring Information.
- When Monitored:
Continuously.
- Set Condition:
When one of the Mirror Fold or Unfold Driver circuits are shorted to battery voltage or the circuit is open for approximately 30 seconds.
1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, erase the DTCs.
3. Cycle the ignition from on to off.
4. Turn the ignition on.
5. Turn the turn signal on, if equipped with turn signal mirror.
6. Turn the puddle lamps on, if equipped with puddle lamp mirror.
7. Turn on the rear window defogger.
8. Operate the Mirror Fold switch in both directions three times.
9. Wait 30 seconds.
10. With the scan tool, read the active DTCs.
Does the scan tool display: B1E6A-15-PASSENGER MIRROR FOLD CONTROL CIRCUIT SHORT TO BATTERY OR OPEN as active?
Yes
- Go To 2
No
- The condition that caused this symptom is currently not present. Check for an intermittent condition by inspecting the related wiring harness for chafed, pierced, pinched and partially broken wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded or contaminated terminals. Repair as necessary.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
2. CHECK (P695) PASSENGER MIRROR FOLD DRIVER CIRCUIT AND (P692) PASSENGER MIRROR UNFOLD DRIVER CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the Passenger Outside Rearview Mirror C2 (Component Side) connector.
3. Measure the resistance between the (P695) Passenger Mirror Fold Driver circuit and the (P692) Passenger Mirror Unfold Driver circuit at the Passenger Outside Rearview Mirror C2 (Component Side) connector.
Is the resistance below 9.0 Ohms?
Yes
- Go To 3
No
- Repair the (P695) Passenger Mirror Fold Driver circuit or the (P692) Passenger Mirror Unfold Driver circuit for an open. If the wiring harness and connector are okay, replace the Passenger Outside Rearview Folding Mirror. Outside Rearview Mirror - Removal.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
3. CHECK (P695) PASSENGER MIRROR FOLD DRIVER CIRCUIT AND (P692) PASSENGER MIRROR UNFOLD DRIVER CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition on.
2. Measure the voltage between ground and the (P695) Passenger Mirror Fold Driver circuit in the Passenger Outside Rearview Mirror C2 (Component Side) connector.
3. Measure the voltage between ground and the (P692) Passenger Mirror Unfold Driver circuit in the Passenger Outside Rearview Mirror C2 (Component Side) connector.
Is there any voltage present in either terminal?
Yes
- Repair the (P695) Passenger Mirror Fold Driver circuit or the (P692) Passenger Mirror Unfold Driver circuit for a short to voltage. If the wiring harness and connector are okay, replace the Passenger Outside Rearview Folding Mirror. Outside Rearview Mirror - Removal.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Go To 4
4. CHECK (P695) PASSENGER MIRROR FOLD DRIVER CIRCUIT FOR A SHORT TO A PASSENGER MIRROR DRIVER CIRCUIT.
1. Turn the ignition off.
2. Measure the resistance between the (P695) Passenger Mirror Fold Driver circuit (C2-1) and all Passenger Mirror Driver circuits in the Passenger Outside Rearview Mirror C2 (Component Side) connector.
Is the resistance below 10K Ohms for any measurement?
Yes
- Repair all circuits with a resistance below 10K Ohms for a short to the (P695) Passenger Mirror Fold Driver circuit. If the wiring harness and connector are okay, replace the Passenger Outside Rearview Mirror. Outside Rearview Mirror - Removal.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Go To 5
5. CHECK (P695) PASSENGER MIRROR FOLD DRIVER CIRCUIT FOR A SHORT TO A PASSENGER MIRROR ACCESSORY DRIVER CIRCUIT
1. Disconnect the Passenger Outside Rearview Mirror C1 (Component Side) connector from the Door Module C1 connector.
2. Measure the resistance between the (P695) Passenger Mirror Fold Driver circuit (C2-1) and each of the Passenger Mirror Accessory Driver circuits in the Passenger Outside Rearview Mirror C2 and C1 (Component Side) connectors.
Is the resistance below 10K Ohms between the (P695) Passenger Mirror Fold Driver circuit and any Passenger Mirror Driver circuit?
Yes
- Repair the (P695) Passenger Mirror Fold Driver circuit for a short to a Passenger Mirror Accessory Driver circuit. If the wiring harness and connector are okay, replace the Passenger Outside Rearview Mirror. Outside Rearview Mirror - Removal.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Inspect the wiring and connectors for damage and repair as necessary. If the wiring and connectors are okay, replace the Door Module. Door Module - Removal.
- Perform the BODY VERIFICATION TEST. Body Verification Test.