Operation CHARM: Car repair manuals for everyone.

U11B0






U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE IMPACT SENSOR 4

Special Tools:










For a complete wiring diagram, refer to the Wiring Information.

Theory of Operation

The right side impact pressure sensor is located in the first row door. The impact pressure sensors perform their own self test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor.

- When Monitored:
The Occupant Restraint Controller (ORC) continuously communicates with the Right Side Impact (Pressure) Sensor 4 over the sensor signal circuit. The sensor communication and on board diagnostics are powered by the ORC signal.

- Set Condition:
This code will set, if the ORC and the Right Side Impact (Pressure) Sensor 4 do not establish and maintain valid data communications. The DTC will become Active after the fault has set for 9 seconds. The DTC will go to Stored after the ORC to Right Side Impact (Pressure) Sensor 4 communication has recovered for 4 seconds.





Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Restraints System Pre-Diagnostic Procedure.

1. VERIFY THAT DTC U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION (PRESSURE) SENSOR 4 IS ACTIVE

NOTE: Make sure the battery is fully charged.

1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.

Does the scan tool display active: U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION (PRESSURE) SENSOR 4?

Yes

- Go To 2

No

- Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Restraints System Intermittent Condition Test.

2. CHECK THE (R140), (R160) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS FOR A SHORT TO VOLTAGE





WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Disconnect the Right Side Impact Pressure Sensor harness connector.
2. Disconnect the ORC harness connector.If equipped with the standard key ignition, use this ignition on warning.

WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
If equipped with the keyless ignition, use this ignition on warning.

WARNING: Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

3. Measure the voltage of the (R140) Right Side Impact Pressure Sensor Signal circuit and (R160) Sensor Ground circuit at the appropriate terminal of the Right Side Impact Pressure Sensor harness connector and ground.

Is there any voltage present?

Yes

- Repair the (R140), (R160) Right Side Impact Pressure Sensor circuits for a short to voltage.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 3

3. CHECK THE (R140) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND





WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Measure the resistance of the (R140) Right Side Impact Pressure Sensor Signal circuit between the appropriate terminal of the Right Side Impact Pressure Sensor harness connector and ground.

Is the resistance below 20 Ohms?

Yes

- Repair the (R140) Right Side Impact Pressure Sensor Signal circuit for a short to ground.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 4

4. CHECK THE (R140), (R160) RIGHT SIDE IMPACT PRESSURE SENSOR CIRCUITS FOR A SHORT TOGETHER




1. Measure the resistance between the (R140) Right Side Impact Pressure Sensor 4 Signal circuit and the (R160) Sensor Ground circuits at the Right Side Impact Pressure Sensor 4 harness connector.

Is the resistance below 20 Ohms?

Yes

- Repair the (R140), (R160) Right Side Impact Pressure Sensor circuits shorted together.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 5

5. CHECK THE (R160) RIGHT SIDE IMPACT PRESSURE SENSOR GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE




1. Connect the (8443-24) to the Occupant Control Module harness connector.
2. Measure the resistance of the (R160) Right Side Impact Pressure Sensor Ground circuit between the Right Side Impact Pressure Sensor harness connector and the appropriate terminal of the (8443-24).

Is the resistance below 1 Ohm?

Yes

- Go To 6

No

- Repair the (R160) Right Side Impact Pressure Sensor Ground circuit for an open or high resistance.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

6. CHECK THE (R140) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL CIRCUIT FOR AN OPEN OR HIGH RESISTANCE




1. Measure the resistance of the (R140) Right Side Impact Pressure Sensor Signal circuit between the a Right Side Impact Pressure Sensor harness connector and the appropriate terminal of the (8443-24).

Is the resistance below 1 Ohm?

Yes

- Go To 7

No

- Repair the (R140) Right Side Impact Pressure Sensor Signal circuit for an open or high resistance.
- Perform the RESTRAINTS VERIFICATION TEST. Restraints System Verification Test.

7. CHECK OPERATION OF THE RIGHT SIDE IMPACT PRESSURE SENSOR
1. Replace the Right Side Impact Pressure Sensor. Impact Sensor - Removal.
2. Reconnect the vehicle body harness to the impact pressure sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.If equipped with the standard key ignition, use this ignition on warning.

WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
If equipped with the keyless ignition, use this ignition on warning.

WARNING: Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

4. Connect the scan tool to the Data Link Connector - use the most current software available.
5. Use the scan tool and erase the stored codes in all airbag system modules.
6. Turn the Ignition Off, and wait five seconds before turning the Ignition On.
7. Wait one minute, and read active codes and if there are none present read the stored codes.

Did the active: U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION PRESSURE SENSOR 4 DTC return?

Yes

- WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

- WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.

- Replace the Occupant Restrain Controller (ORC). Occupant Restraint Controller - Removal.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Repair is complete.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.