Speed Control Switch - Installation

INSTALLATION

LEFT-HAND DRIVE

CHRYSLER

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.





1. Position the speed control switch pod (2) to the back of the right steering wheel spoke front bezel (1).
2. Install and tighten the three screws (3) that secure the switch to the bezel. Tighten the screws securely.
3. Position the right front spoke bezel close enough to the steering wheel to reconnect the steering wheel wire harness connection to the connector receptacle integral to the inboard end of the speed control switch pod.
4. Position the right front spoke bezel and speed control switch pod as a unit to the steering wheel. Be certain that the steering wheel wire harness is not pinched.





5. Install and tighten the two screws (1) that secure the right front spoke bezel (2) within the hub cavity of the steering wheel. Tighten the screws securely.





6. From the back of the right lower spoke of the steering wheel (1), install and tighten the screw (2) that secures the right spoke front bezel and speed control switch unit to the steering wheel. Tighten the screw securely.
7. Reinstall the driver airbag onto the steering wheel. Driver Air Bag - Installation.
8. Reconnect the battery negative cable.

DODGE

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.





1. Position the speed control switch pod (2) and the mounting adapter plate (3) to the back of the right steering wheel spoke front bezel (1).
2. Install and tighten the three screws (4) that secure the mounting adapter plate and the switch to the bezel. Tighten the screws securely.
3. Position the right front spoke bezel close enough to the steering wheel to reconnect the steering wheel wire harness connection to the connector receptacle integral to the inboard end of the speed control switch pod.
4. Engage the lip on the inboard side of the bezel under the edge of the driver airbag trim cover.
5. Position the right front spoke bezel, mounting adapter plate and speed control switch pod as a unit to the steering wheel. Be certain that the steering wheel wire harness is not pinched.





6. From the back of the right horizontal spoke of the steering wheel (1), install and tighten the screw (3) between the remote radio switch (4) and the floating horn switch mounting screw clearance hole (2) that secures the mounting adapter plate, right spoke front bezel and speed control switch to the steering wheel spoke. Tighten the screw securely.
7. Reconnect the battery negative cable.

RIGHT-HAND DRIVE

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.





1. Position the speed control switch (3) to the steering wheel.
2. Install and tighten the three screws (2) that secure the speed control switch to the steering wheel armature. Tighten the screws to 1.6 Nm (15 in. lbs.).
3. Reconnect the steering wheel wire harness connector (1) to the speed control switch connector receptacle.
4. Reinstall the Driver Air Bag (DAB) onto the steering wheel. Driver Air Bag - Installation.
5. Reconnect the battery negative cable.