U0176

U0176-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 2

Special Tools:

For a complete wiring diagram, refer to the Wiring Information.

Theory of Operation

The impact sensors perform their own self test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor. Refer to the enclosed graphic as a reference of specific Side Impact Satellite Acceleration, Side Impact Satellite Pressure, and Up-Front Satellite Acceleration sensor locations on the vehicle. It is important to review this graphic thoroughly to understand the specific area of diagnosis you are looking to complete.

The Up-Front Right and Up-Front Left Satellite Acceleration Sensors are located behind the Front End Module carrier in the engine area. The number 1 side sensors are located in the 1st row door area with the number 1 side sensor being on the passenger side (Right Side Satellite Pressure Sensor 1) and the number 1 side sensor also being on the driver side (Left Side Satellite Pressure Sensor 1). The number 4 side sensors are located in the "B" pillar area just past the 1st row doors. The number 4 side sensor is located on the passenger side (Right Side Satellite Acceleration Sensor 4) and the number 4 side sensor is also located on the driver side (Left Side Satellite Acceleration Sensor 4). The number 2 side sensors are located in the "C" pillar area just past the 2nd row doors. The number 2 side sensor is located on the passenger side (Right Side Satellite Acceleration Sensor 2) and the number 2 side sensor is also located on the driver side (Left Side Satellite Acceleration Sensor 2). The number 3 side sensors are located in the 3rd row area just above the rear axle. The number 3 side sensor is located on the passenger side (Right Side Satellite Acceleration Sensor 3) and the number 3 side sensor is also located on the driver side (Left Side Satellite Acceleration Sensor 3).

- When Monitored:
The ORC monitors communication with the impact sensor continuously.

- Set Condition:
This DTC sets when the ORC no longer receives notification of the status update from the impact sensor. Once set, this DTC is latched for the entire ignition cycle.

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Restraints System Pre-Diagnostic Procedure.

1. DETERMINE ACTIVE OR STORED DTC

NOTE: Make sure the battery is fully charged.

1. Turn the ignition on.
2. Using the scan tool, read ORC DTCs.

Is the DTC active or stored?

ORC - ACTIVE DIAGNOSTIC TROUBLE CODE (DTC)

- Go To 2

ORC - STORED DTC

- Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. . Restraints System Intermittent Condition Test

2. CHECK FOR ADDITIONAL ACTIVE SATELLITE SENSOR DTCS

NOTE: The scan tool, (8443-28), and a DVOM are required to perform the following tests.

1. Using the scan tool, read all active ORC DTCs.

Is DTC U0173-LOST COMMUNICATION W/LEFT SIDE SATELLITE ACCELERATION SENSOR 2 also active?

Yes

- Go To 8

No

- Go To 3

3. CHECK (R18) RIGHT SIDE IMPACT SENSOR 2 SIGNAL CIRCUIT FOR AN OPEN

1. Measure the resistance of the (R20) Right Side Impact Sensor 2 Ground circuit between the Right Side Impact Sensor 2 harness connector and the (8443-28).

Is the resistance below 1.0 Ohm?

Yes

- Go To 5

No

- Repair or replace the (R20) Right Side Impact Sensor 2 Ground circuit for an open.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

5. CHECK (R18) RIGHT SIDE IMPACT SENSOR 2 SIGNAL CIRCUIT FOR A SHORT TO THE (R20) RIGHT SIDE IMPACT SENSOR 2 GROUND CIRCUIT

1. Measure the resistance between the (R18) Right Side Impact Sensor 2 Signal circuit and the (R20) Right Side Impact Sensor 2 Ground circuit at the Right Side Impact Sensor 2 harness connector.

Is the resistance below 5K Ohms?

Yes

- Repair or replace the (R18) Right Side Impact Sensor 2 Signal circuit for a short to the (R20) Right Side Impact Sensor 2 Ground circuit.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 6

6. CHECK (R18) RIGHT SIDE IMPACT SENSOR 2 SIGNAL CIRCUIT FOR A SHORT TO GROUND

1. Measure the resistance of the (R18) Right Side Impact Sensor 2 Signal circuit between ground and the Right Side Impact Sensor 2 harness connector.

Is the resistance below 6K Ohms?

Yes

- Repair or replace the (R18) Right Side Impact Sensor 2 Signal circuit for a short to ground.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 7

7. CHECK (R18) RIGHT SIDE IMPACT SENSOR 2 SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE

If the vehicle is equipped with the standard key ignition, follow this ignition on warning.

WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
If the vehicle is equipped with the keyless ignition, follow this ignition on warning.

WARNING: Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Measure the voltage of the (R18) Right Side Impact Sensor 2 Signal circuit between the Right Side Impact Sensor 2 harness connector and ground.

Is there any voltage present?

Yes

- WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
- Repair or replace the (R18) Right Side Impact Sensor 2 Signal circuit for a short to voltage.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test. If DTC U0176-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 2 is still active, Go To 8 Otherwise, test complete.

8. CHECK (R20) RIGHT SIDE IMPACT SENSOR 2 GROUND CIRCUIT AND (R19) LEFT SIDE IMPACT SENSOR 2 GROUND CIRCUIT FOR A SHORT TO VOLTAGE

WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Disconnect the Left Side Impact Sensor 2 harness connector.
2. Disconnect the Right Side Impact ACCEL) Sensor 2 harness connector.
3. Disconnect the ORC harness connectors.

NOTE: Check the connectors - Clean and repair as necessary.

4. Connect the (8443-28) to the ORC harness connectors.

WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

5. Measure the voltage of the (R19) Left Side Impact Sensor 2 Ground circuit between the (8443-28) connector C1A cavity 4 and ground.
6. Measure the voltage of the (R20) Right Side Impact Sensor 2 Ground circuit between the (8443-28) and ground.

Is there any voltage present on either circuit?

Yes

- WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
- Repair or replace the impact sensor circuit with voltage present for a short to voltage.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 9

9. CHECK OPERATION OF THE RIGHT SIDE IMPACT SENSOR 2

WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Replace the Right Side Impact Sensor 2. Occupant Restraint Controller - Removal.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Repair is complete.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.