Part 5

OPERATION - LHD

NO FUSE INDICATOR

The no fuse indicator gives an indication to the vehicle operator when the Ignition Off Draw (IOD) fuse is ineffective or is not installed. This indicator is controlled by the instrument cluster logic circuit based upon cluster programming and electronic messages received over the CAN data bus from the TIPM.

The no fuse indicator function of the odometer VFD unit is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the odometer VFD no fuse indication will always be OFF when the ignition switch is in any position except ON or START. The instrument cluster will turn ON the no fuse indicator for the following reasons:

- No Fuse Indicator Lamp-On Message - Each time the ignition switch is turned to the ON position and the cluster does not receive battery voltage from the IOD fuse, a no fuse indicator lamp-ON indicator will be illuminated. The indicator remains illuminated for about three seconds, until the IOD fuse is installed, until the trip odometer reset switch button is depressed or until the ignition switch is turned to the OFF position, whichever occurs first.

The TIPM continually monitors the IOD circuit to determine the status of the IOD fuse. The TIPM then sends the proper lamp-ON or lamp-OFF message to the CCN.

CHANGE OIL INDICATOR

The change oil indicator gives an indication to the vehicle operator when a duty-cycle algorithm contained within the software of the PCM/ECM determines that a recommended oil change interval has been attained. This indicator is controlled by the instrument cluster logic circuit based upon cluster programming and electronic messages received over the CAN data bus from the PCM/ECM.

The change oil indicator function of the odometer or Electronic Vehicle Information Center (EVIC) VFD unit is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the odometer or EVIC VFD change oil indication will always be OFF when the ignition switch is in any position except ON or START. The instrument cluster will turn ON the change oil indicator for the following reasons:

- Change Oil Indicator Lamp-On Message - Each time the ignition switch is turned to the ON position and the cluster receives an electronic change oil indicator lamp-ON message from the PCM/ECM indicating that a duty-cycle based recommended oil change interval has been attained, the change oil indicator will be illuminated for about three seconds, until the trip odometer reset switch button or an EVIC steering wheel switch button is depressed, or until the ignition switch is turned to the OFF position, whichever occurs first.
- Change Oil Indicator Reset Procedure - Once an engine oil change has been completed, the PCM/ECM duty cycle counters can be reset using the following procedure. Turn the ignition switch to the ON position, but DO NOT start the engine. Slowly depress and release the accelerator pedal fully three times within ten seconds. Turn the ignition switch to the OFF position. If the change oil indicator illuminates the next time the engine is started, repeat this procedure.

The PCM/ECM continually monitors numerous sensor inputs to determine the duty-cycles to which the engine is being subjected. A pre-programmed algorithm within the PCM/ECM then determines when to send the proper lamp-ON or lamp-OFF message to the CCN.

REAR FOG LAMP INDICATOR

The rear fog lamp indicator gives an indication to the vehicle operator whenever the rear fog lamps are illuminated. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the TIPM over the CAN data bus.

The rear fog lamp indicator LED is completely controlled by the instrument cluster logic circuit, and that logic will allow this indicator to operate whenever the instrument cluster receives a battery current input on the fused B(+) circuit. Therefore, the LED can be illuminated regardless of the ignition switch position. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the rear fog lamp indicator for the following reasons:

- Rear Fog Indicator Lamp-On Message - Each time the cluster receives an electronic rear fog indicator lamp-ON message from the TIPM indicating the rear fog lamps are turned ON, the rear fog lamp indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the TIPM, or until the exterior lamp load shedding (battery saver) timed interval expires, whichever occurs first.

The TIPM continually monitors electronic exterior lighting request messages from the CCN to determine the appropriate outputs to the rear fog lamps. The TIPM activates or deactivates the rear fog lamps then sends the proper lamp-ON or lamp-OFF message back to the CCN.

SEATBELT INDICATOR

The seatbelt indicator gives an indication to the vehicle operator of the status of the driver side front seat belt. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and a hard-wired input from the seatbelt switch on the driver side front seat belt retractor through the seat belt switch sense circuits.

The seatbelt indicator also includes a programmable enhanced seatbelt reminder or BELTMINDER feature that is enabled when the vehicle is shipped from the factory. This BELTMINDER feature can be disabled and enabled by using a specific programming event sequence Testing and Inspection , or by using a diagnostic scan tool.

The seatbelt indicator LED is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the seatbelt indicator for the following reasons:

- Seatbelt Reminder Function - Each time the cluster receives a battery current input on the fused ignition switch output (run-start) circuit, the indicator will be illuminated as a seatbelt reminder for about six seconds, or until the ignition switch is turned to the OFF position, whichever occurs first. This reminder function will occur regardless of the status of the seatbelt switch inputs to the cluster.
- Front Seatbelt Not Buckled - Beltminder Active - Following the seatbelt reminder function, each time the cluster receives an open circuit message on the Can B Data Bus from the TIPM, (seatbelt switch open = seatbelt unbuckled) with the ignition switch in the START or ON positions, the indicator will be illuminated. In addition, if the front seat belt remains unbuckled about 4 seconds after the conclusion of the seatbelt reminder function, the seatbelt indicator will begin to cycle between flashing ON and OFF for 3 seconds, then lighting solid for 2 seconds. The seatbelt indicator will continue to cycle between flashing and solid illumination for 13 complete cycles, until the seat belt switch sense input to the cluster is a closed circuit to ground (seatbelt switch closed = seatbelt buckled), or until the ignition switch is turned to the OFF position, whichever occurs first.
- Front Seatbelt Not Buckled - Beltminder Inactive - Following the seatbelt reminder function, each time the cluster detects an open circuit on the seat belt switch sense circuit (seatbelt switch open = seatbelt unbuckled) with the ignition switch in the START or ON positions, the indicator will be illuminated. The seatbelt indicator remains illuminated until the seat belt indicator input to the cluster is a closed circuit to ground (seatbelt switch closed = seatbelt buckled), or until the ignition switch is turned to the OFF position, whichever occurs first.

The seatbelt switch is connected in series between ground and the seat belt switch sense circuit input to the instrument cluster. The seatbelt switch input to the CCN circuitry may be diagnosed using conventional diagnostic tools and procedures. Refer to the appropriate wiring information.

SECURITY SYSTEM INDICATOR

The security indicator gives an indication to the vehicle operator when the Vehicle Theft Security System (VTSS) is arming or is armed. On vehicles equipped with the Sentry Key Immobilizer System (SKIS), the security indicator also gives an indication to the vehicle operator of the status of the SKIS. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming, and electronic security indicator request messages received by the cluster from the TIPM or the WIN, over the CAN data bus.

The security indicator LED is completely controlled by the instrument cluster logic circuit, and that logic will allow this indicator to operate whenever the instrument cluster receives a battery current input on the fused B(+) circuit. Therefore, the LED can be illuminated regardless of the ignition switch position. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. Depending upon the programmed condition, the indicator can be illuminated solid, flashed at a slow rate (0.5 Hertz, 12.5 percent duty cycle), or flashed at a fast rate (1 Hertz, 50 percent duty cycle). Each time the ignition switch is turned to the ON position the security indicator illuminates for about two seconds as a bulb test. The entire bulb test is a function of the WIN. The instrument cluster will turn ON the security indicator for the following reasons:

- Security Indicator Lamp-On Message - During the 16 second VTSS arming function, the TIPM will request the cluster flash the security indicator ON and OFF repeatedly at a steady, fast rate to indicate that the VTSS is in the process of arming. Following successful VTSS arming, the TIPM will request the cluster flash the security indicator ON and OFF continuously at a slower rate to indicate that the VTSS is armed. The security indicator continues flashing at the slower rate until the VTSS is disarmed or triggered. If the VTSS has alarmed and rearmed, the TIPM will request the cluster flash the security indicator at a steady, slow rate for about 30 seconds after the VTSS is disarmed.
- SKIS Indicator Lamp-On Message - Each time the cluster receives an electronic SKIS indicator lamp-ON message from the WIN, the security indicator will be illuminated. The indicator can be flashed ON and OFF, or illuminated solid, as dictated by the WIN message. The indicator remains illuminated solid or continues to flash until the cluster receives a lamp-OFF message from the WIN, or until the ignition switch is turned to the OFF position, whichever occurs first. For more information on the SKIS and the security indicator control parameters, Vehicle Theft Security System - Operation.
- Communication Error - If the cluster receives no lamp-ON or lamp-OFF messages from the TIPM or the WIN for 10 consecutive message cycles, the security indicator is illuminated by the instrument cluster. The indicator remains controlled and illuminated by the cluster until a valid lamp-ON or lamp-OFF message is received from the WIN.

The TIPM sends electronic security indicator request messages to control the security indicator whenever the ignition switch is in the OFF position and the VTSS is arming, armed, or alarming. Whenever the ignition switch is in the ON or START positions, the WIN performs a self-test to decide whether the SKIS is in good operating condition and whether a valid key is present in the ignition lock cylinder. The WIN then sends the proper lamp-ON or lamp-OFF message to the CCN. If the cluster flashes the security indicator upon ignition ON, or turns ON the security indicator solid after the bulb test, it indicates that a SKIS malfunction has occurred or that the SKIS is inoperative.