B19CF

B19CF-RIGHT POWER SLIDING DOOR DRIVE OPEN DIRECTION EXCESSIVE TIME

For a complete wiring diagram, refer to the Wiring Information.

- When Monitored:
Whenever the Right Power Sliding Door Motor is in operation.

- Set Condition:
This code will set when the Right Power Sliding Door module senses the Right Power Sliding Door Motor has taken longer than 20 seconds to complete a power opening operation. It will also set if an ignition crank message is sent, lasting longer than 15 seconds, during an opening operation.





Diagnostic Test

1. CHECK FOR DTCS
1. With the scan tool, record the DTCs and any power sliding door inhibitors.
2. Erase the DTCs.
3. Turn the ignition off, wait 10 seconds, then turn the ignition on.
4. Attempt to operate the Right Power Sliding Door.
5. With the scan tool, read the DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 2

No

- Test complete. The condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

2. CHECK THE RIGHT POWER SLIDING DOOR
1. Examine the Right Power Sliding Door for proper alignment, worn or binding rollers and hinges, loose/damaged weatherstrip, and track assembly for wear or anything that would cause an obstruction to proper operation.
2. Manually operate the Right Power Sliding Door on a known good vehicle and notice the effort needed to open and close for comparison.
3. Especially notice the effort needed to unlatch and close the Right Power Sliding Door during a power opening operation.

Were there any mechanical problems found?

Yes

- Sliding Door Adjustments and perform the appropriate repairs and adjustments.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 3

3. PERFORM THE POWER SLIDING DOOR LEARN CYCLE
1. Programming and Relearning and perform the Power Sliding Door Learn Cycle procedure (Sliding Door Open/Close Tests). If both tests "Pass" continue on here.
2. With the scan tool, erase the DTCs.
3. Turn the ignition off, wait 10 seconds, then turn the ignition on.
4. If possible, operate the Right power sliding door several times.
5. With the scan tool, read the active DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 4

No

- Test complete. The module has relearned the door travel limits, resistance to door travel, door position, etc. Recheck for any intermittent door dragging or sticking conditions.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

4. CHECK THE POWER SLIDING DOOR CLUTCH
1. Manually open the Sliding Door part way.
2. With the scan tool, actuate the Drive Clutch.
3. Try to manually move the Sliding Door and notice the effort to move it.

Was it almost impossible to move the Sliding Door when the clutch was engaged?

No

- Go To 6

Yes

- Go To 5

5. CHECK THE RIGHT POWER SLIDING DOOR MODULE AND MOTOR CONNECTORS





NOTE: At this time it will be necessary to remove the Power Sliding Door Drive Unit Assembly from the vehicle.

1. Turn the ignition off.
2. Remove the Power Sliding Door Drive Unit Assembly from the vehicle.
3. Disconnect the Power Sliding Door Module C2 (8 way) connector.
4. Check the Power Sliding Door Module C2 (8 way) and the Motor (8 way) connectors for proper terminal contact, corrosion, damaged terminals, or pinched/broken wires. Check for any mechanical problems.

Were any wiring or mechanical problems found?

Yes

- Repair any wiring or mechanical problems.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Replace the Right Power Sliding Door Module and Drive Unit Assembly.
- Programming and Relearning and perform the Power Sliding Door Learn Cycle procedure.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

6. CHECK THE POWER SLIDING DOOR MODULE





NOTE: At this time it will be necessary to remove the Power Sliding Door Drive Unit Assembly from the vehicle.

1. Turn the ignition off.
2. Remove the Power Sliding Door Drive Unit Assembly from the vehicle.
3. Disconnect the Power Sliding Door Module connector.
4. Remove the Power Sliding Door Module from the track.
5. Reconnect the C383 Right Body 4 way harness connector.
6. Re-connect the PSD Module connector to the module.
7. Turn the ignition on.
8. Measure the voltage between the Door Motor Clutch Driver circuit and the Door Motor Clutch Return circuit in the PSDM C2 (component side) 8 way connection.
9. With the scan tool, actuate the Drive Clutch Engage.

Is the voltage between 12.5 and 14.0 volts when the clutch is activated?

Yes

- Replace the Power Sliding Door Drive Unit.
- Programming and Relearning and perform the Power Sliding Door Learn Cycle procedure.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Replace the Power Sliding Door Module.
- Programming and Relearning and perform the Power Sliding Door Learn Cycle procedure.
- Perform the BODY VERIFICATION TEST. Body Verification Test.