P0140

P0140-O2 SENSOR 1/2 NO ACTIVITY DETECTED

Special Tools:






For a complete wiring diagram, refer to the Wiring Information.





Theory of Operation

The Oxygen Sensors (O2 Sensor) are used for fuel control and catalyst monitoring. Each O2 Sensor measures the oxygen content of the exhaust stream. When the engine is started, the Powertrain Control Module (PCM) operates in an Open Loop mode, ignoring the O2 Sensor signal voltage while calculating the air-to-fuel ratio. The heating elements inside each O2 Sensor heats the sensor to bring it to operating conditions faster. This allows the system to enter Closed Loop earlier and the PCM to calculate the air-to-fuel ratio sooner. While the engine runs, the O2 Sensor heats up and begins to generate a voltage within a range of 0-1,275 mV. Once sufficient O2 Sensor voltage fluctuation is observed by the PCM, Closed Loop is entered. The PCM uses the O2 Sensor voltage to determine the air-to-fuel ratio. An O2 Sensor voltage that increases toward 1,000 mV indicates a rich fuel mixture. An O2 Sensor voltage that decreases toward 0 mV indicates a lean fuel mixture. The Powertrain Control Module (PCM) makes short term and long term fuel corrections to maintain stoichiometric fuel/air ratio for best catalytic converter efficiency. Short term fuel correction is based on upstream O2 Sensor output and is designed for quick engine response. The long term fuel correction compensated for variations in the engine specifications, sensor tolerances and component aging and is designed to correct rich and lean conditions over a longer period of time.

- When Monitored:
With the engine running, vehicle speed between 32.2 kph (20 mph) and 112.65 kph (70 mph), throttle open for a minimum of 240 seconds, engien speed between 1024 RPM and 3008 RPM, calculated engine load between 29% and 80%.

- Set Condition:
The Powertrain Control Module (PCM) detects that the oxygen sensor signal switches from lean to rich less than 16 times within 20 seconds during monitoring. Two Trip Fault. Three good trips to turn off the MIL.





Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Pre-Diagnostic Troubleshooting Procedure.

Diagnostic Test

1. ACTIVE DTC

NOTE: After the repairs have been made, verify proper O2 Sensor operation. If all the O2 Sensor voltage readings have not returned to normal, follow the diagnostic procedure for the remaining O2 Sensors.

NOTE: Check for contaminants that may have damaged the O2 Sensor: contaminated fuel, unapproved silicone, oil and coolant.

1. Start the engine and allow the engine to reach normal operating temperature.
2. Test drive the vehicle according to the set conditions.
3. With the scan tool, select View DTCs.

Is the DTC Active or Pending at this time?

Yes

- Go To 2

No

- Perform the INTERMITTENT CONDITION diagnostic procedure. Intermittent Condition Test.

2. CHECKING THE EXHAUST SYSTEM FOR LEAKS
1. Turn the ignition off.
2. Raise the vehicle.

WARNING:
The normal operating temperature of the exhaust system is very high. Never work around or attempt to service any part of the exhaust system until it has cooled. Special care should be taken when working near the catalytic converter. The temperature of the converter rises to a high level after a short period of engine operating time.

3. Connect Exhaust Cone (8404-EC) or (8404-EC) to Air Pressure Regulator (with hose) W-18-MIL-1146AS.

CAUTION:
The air pressure must not exceed 27.6 kPa (4 psi), otherwise engine damage can occur.

4. Attach shop air to the air pressure regulator.
5. Adjust the Air Pressure Regulator to 27.6 kPa (4 psi).
6. Insert the exhaust cone into the vehicle tail pipe.
7. If the vehicle is equipped with dual exhaust. Use the (8404-ECT) with equipped attached plug, plug one side of the dual exhaust pipe. Pressurize the other as described above.
8. Apply Mopar(R) Air Leak Detector PN# 05191804AA (or an equivalent leak finder liquid) to the following areas:
- All welded joints from the exhaust manifold to 152.4 mm (6 inches) behind the downstream O2 Sensor
- O2 Sensor seal points
- O2 Sensor boss welds
- Flange/joint connection(s)
- Exhaust manifold to cylinder head connection(s)
- EGR solenoid gasket base and tube seal points (if equipped)

9. Watch for the liquid/soapy water to bubble.
10. Use the following definitions to help determine if system or component repair/replacement is necessary:
- Type 1 Leak is defined as a leak where very small foam like bubbles 1 mm (0.04 of an inch) or less appear. Any Type 1 or greater leaks found in welded joints, O2 Sensor seal points or O2 sensor boss welds must be repaired or the component must be replaced.
- Type 2 Leak is defined as a leak where larger bubbles pea size, 8 mm (0.3 of an inch) or greater appear. Any Type 2 or greater leaks found in flange or joint connections, exhaust manifold to cylinder head connections or EGR gasket and tube seal points must be repaired or the components must be replaced.






11. If a leak is found that matches the above definition, repair or replace the component as necessary.
12. Once the repair is complete, repeat the procedure to verify that all leaks have been repaired.

Were any exhaust leaks found?

Yes

- Repair or replace the leaking exhaust parts as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Go To 3

3. (K141) O2 SENSOR 1/2 SIGNAL CIRCUIT
1. Turn the ignition off.
2. Disconnect the O2 Sensor 1/2 harness connector.
3. Ignition on, engine not running.
4. Measure the voltage on the(K141) O2 Sensor 1/2 Signal circuit in the O2 Sensor1/2 harness connector.

Is the voltage between 0.12 and 0.09 volts?

Yes

- Go To 4

No

- Check the O2 Sensor 1/2 Signal circuit for a short to ground, open or short to voltage. If OK, replace and program the PCM. .
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

4. (K904) O2 SENSOR RETURN CIRCUIT
1. Measure the voltage on the (K904) O2 Sensor Return circuit at the O2 Sensor1/2 harness connector.

Is the voltage at 0.11 volts?

Yes

- Go To 5

No

- Check the (K904) O2 Sensor Return circuit for a short to ground, open or short to voltage. If OK, replace and program the PCM. .
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

5. OXYGEN SENSOR
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Oxygen Sensor 1/2 and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Perform any Technical Service Bulletins that may apply.

Were any problems found?

Yes

- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

No

- Replace the Oxygen Sensor 1/2. .
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.