Oil Pan, Engine

Camshaft Sprocket Bolt 23-38 Nm (19-28 ft lb)
Camshaft Thrust Plate 17-21 Nm (13-16 ft lb)
Connecting Rod Nut 26-33 Nm (19-24 ft lb)
Crankshaft Pulley (Cast) to Crankshaft 115-130 Nm (85-96 ft lb)
Cylinder Head Bolt (Tighten to Yield) In Sequence
Step 1 30 Nm (22 ft lb)
Step 2 70-75 Nm (51-55 ft lb)
Step 3 Turn 90 Degrees
Flywheel to Crankshaft 64-70 Nm (47-52 ft lb)
Front Cover to Cylinder Block 17-20 Nm (13-16 ft lb)
Intake Manifold (Bolt/Nut) In Sequence
Step 1 Hand Start and Snug Nuts at Positions 3 and 4
Step 2 4-8 Nm (3-6 ft lb)
Step 3 8-15 Nm (6-11 ft lb)
Step 4 15-21 Nm (11-15 ft lb)
Step 5 21-25 (15-18 ft lb) [1]
Upper Intake (Plenum)
1. Tighten all bolts (6) to 10 Nm (7 ft lb).
2. Then tighten all bolts to 21-25 Nm (15-18 ft lb).
Throttle Body to Upper Intake 9-13 Nm (6-10 ft lb)
Intake Manifold Stud to Cylinder Block 14-16 Nm (10-12 ft lb)
Main Bearing Cap Bolt 88-102 Nm (65-75 ft lb)
Timing Pointer to Front Cover 7-9 Nm (5-7 ft lb)
Oil Pump Pick Up Tube to Pump 9-13 Nm (6-10 ft lb)
Oil Pickup Tube Support to Main Cap (Nut) 17-21 Nm (12-15 ft lb)
Oil Pump Case 9-13 Nm (6-10 ft lb)
Oil Pan to Cylinder Block In Sequence 7-10 Nm (5-8 ft lb)
Oil Filter Adaptor to Cylinder Block (Bolt) 20-40 Nm (15-30 ft lb)
Oil Pan Drain Plug 21-28 Nm (15-21 ft lb)
Oil Filter [2]
Rocker Cover to Cylinder Head 4-7 Nm (3-5 ft lb)
Rocker Arm Shaft Support Bolt 59-67 Nm (43-50 ft lb)
Water Pump to Front Cover 9-12 Nm (7-9 ft lb)
Water Outlet Connection 9-12 Nm (6-9 ft lb)
Water Jacket Drain Plug 20-25 Nm (14-18 ft lb)
Spark Plug 25-38 Nm (18-28 ft lb)
Alternator Mounting Bracket to Cylinder Block 40-55 Nm (29-40 ft lb)
Alternator Mounting Bracket to Cylinder Head
M-8(2) 20-30 Nm (14-22 ft lb)
M-10 40-55 Nm (29-40 ft lb)
Alternator Pivot Bolt 61-82 Nm (45-61 ft lb)
Alternator Adjustment Arm to Front Cover 70-95 Nm (60-70 ft lb)
Alternator Adjustment Arm to Alternator 70-95 Nm (60-70 ft lb)
Air Conditioning Pulley to Crank Pulley 26-38 Nm (19-28 ft lb)
Fan to Fan Clutch 8-11 Nm (6-8 ft lb)
Fan Clutch to Water Pump Hub 21-34 Nm (15-25 ft lb)
Exhaust Manifold to Cylinder Head (Bolt) 27-40 Nm (20-30 ft lb)
Exhaust Manifold to Cylinder Head (Stud) 27-40 Nm (20-30 ft lb)
Heat Shield Manifold Stud 5-7 Nm (50-65 in lb)
Knock Sensor Assembly to Block 40-54 Nm (30-40 ft lb)
EGR 3-10 Nm (2-7 ft lb)
EGR Valve to Plenum 21-25 Nm (15-18 ft lb)
Idle Air Bypass Valve to Plenum 9-13 Nm (7-10 ft lb)
Fuel Rail to Intake Manifold 9-13 Nm (7-10 ft lb)
Fuel Pressure Regulator to Fuel Rail 9-13 Nm (7-10 ft lb)
Timing Chain Guide to Block 9-13 Nm (7-10 ft lb)
Timing Chain Tensioner to Block 9-13 Nm (7-10 ft lb)
Oil Level Indicator Tube to Manifold Nut Stud 40-55 Nm (30-40 ft lb)
Pulley/Water Pump 20-30 Nm (14-22 ft lb)
[1] Repeat After Warm Up.
[2] One-half turn after gasket contacts sealing surface with oiled gasket.