Tightening Specifications
| Specific Applications | Connecting Rod Nut | 55-61 |
| Cylinder Front Cover | 17-24 | |
| Cylinder Head Bolts (1) | - (l) progressively increase the tightness in three steps using this sequence: 1st step-Tighten all bolts to 67-75 Nm (50-55 ft-lb). 2nd step-Tighten all bolts to 82-88 Nm (60-65 ft-lb). 3rd step-Tighten all bolts to 94-115 Nm (70-85 ft-lb). | |
| Damper to Crankshaft | 177-203 | |
| EGR Valve to Carburetor Spacer or Intake Manifold | 17-24 | |
| Flywheel to Crankshaft | 102-115 | |
| Main Bearing Cap Bolts | 82-94 | |
| - | Manifold to Cylinder Head - Intake (2) | 30-43 (2) progressively increase the tightness in three steps. |
| - | Manifold to Cylinder Head - Exhaust (2) | 30-43 (2) progressively increase the tightness in three steps. |
| Oil Filter Insert to Cylinder Block/Adapter | 20-48 | |
| Oil Filter Adapter to Cylinder Block | 55-67 | |
| Oil Filter to Adapter or Cylinder Block | 1/2 Turn after Gasket Contacts Sealing Surface- Oiled Gasket | |
| Oil Inlet Tube to Pump | 14-20 | |
| Oil Pan Drain Plug | 21-33 | |
| Oil Pan to Cylinder Block (2) | 14-17 | |
| Oil Pump to Cylinder Block | 14-20 | |
| Oil Inlet Tube to Main Bearing Cap | 30-43 | |
| Pulley to Damper Bolt | 48-67 | |
| Rocker Arm Bolt | 24-31 | |
| Spark Plug to Cylinder Head | 14-20 | |
| Valve Rocker Arm Cover | 7.9-11.9 | |
| Valve Push Rod - Cover to Cylinder Block | 2.8-3.9 | |
| Water Outlet Housing | 17-24 | |
| Water Pump to Block/Front Cover | 17-24 | |
| Alternator Bracket to Cylinder Block - Bolt | 41-61 | |
| Alternator Bracket to Cylinder Block Bolt | 41-61 | |
| Alternator Adjusting Arm to Cylinder Block Bolt | 26-36 | |
| Alternator Adjusting Arm to Alternator Bolt | 33-54 | |
| Thermactor Pump Pivot Bolt | 41-48 | |
| Thermactor Pump Adjusting Arm to Pump | 30-43 | |
| Thermactor Pump Pulley to Pump Hub | 17-24 | |
| Thermactor Pump Bracket to Cylinder Block | 30-43 | |
| Fuel Filter to Carburetor/Pump | 10-11 | |
| Carburetor Attaching Nuts | 17-20 | |
| Camshaft Thrust Plate to Cylinder Block | 16-24 | |
| Fuel Pump to Cylinder Block/Front Cover | 17-24 | |
| Carburetor Mounting Stud | 7-13 | |
| Distributor Clamp down | 24-33 | |
| Intake Manifold Vacuum Fittings | 8-13 | |
| Timing Pointer to Front Cover | 17-24 | |
| Thermactor Air Manifold to Cylinder Head (Nut and Ferrule Assembly) | 19-22 | |
| Thermactor Air Check Valve to Thermactor Air Manifold | 22-26 | |
| Pressure Plate and Cover Assembly to Flywheel | 16-25 | |
| Lower Intake Manifold to Head | 30-43 | |
| EGR Tube | 33.8-47.5 | |
| EGR Valve to Upper Intake Manifold | 17-25 | |
| Cooling Manifold | 4-5.6 | |
| Upper Intake Manifold to Lower Intake Manifold Bolts | 16.2-24.4 | |
| Throttle Body to Upper Intake Manifold | 16-24 | |
| Air Bypass Valve to Throttle Body | 8-11 | |
| Throttle Position Sensor to Throttle Body | 2-3 | |
| Fuel Pressure Regulator to Injector Manifold | 3-4.5 | |
| Fuel Injector Manifold to Fuel Charging Assembly | 16-20 | |
| Coil Bracket to Manifold Stud | 5.9-7.4 | |
| Throttle Cable Bracket to Manifold | 11-13 |