Part 1

ASSEMBLY
Transmission














Special Tool(s)

1. Thoroughly clean the transmission case and extension housing in solvent and blow dry with compressed air.





2. Inspect the transmission case for the following:
1. stripped bolt hole threads.
2. Gasket and mating surfaces for burrs or nicks.
3. Obstructions to vent and fluid passages.
^ Cracks or warpage.





3. Inspect the extension housing for cracks, burrs or warpage.





4. Inspect case bearing for damage. Install new components as needed. Follow steps 6-8 if replacing the case bearing. If not replacing the case bearing, proceed to Step 8.





5. Using the special tool, remove the case bearing.
^ Use an oil stone to remove any nicks or burrs in the bearing case bore.





6. Inspect the rear case inner race for burrs, nicks and scoring. If any damage has been found a new case will need to be installed.





7. CAUTION: Make sure bearing seal ring is facing drive handle.

Install a new case bearing.
1. Assemble the special tool.
2. Position new case bearing onto special tool.





8. Using the special tool, tap case bearing into case bearing bore.





9. Install the special tool on the rear of the transmission case.





10. Attach the fixture arm of the special tool as shown.





11. WARNING: Make sure the lock pin on the special tool is secure. Failure to follow these instructions may result in personal injury.

Install transmission into the special tool.
^ Rotate the transmission so that the fluid pan rail is facing up.





12. Using the special tool, install the manual control lever shaft seal.
^ Lubricate the manual control lever shaft seal with petroleum jelly.





13. Assemble the manual valve inner lever and parking lever actuating rod as shown.





14. Install the manual control lever shaft.





15. CAUTION: Use care not to damage the fluid pan rail surface when installing the retaining pin.

NOTE: Align the manual control lever shaft alignment groove with the manual control lever shaft spring pin bore in the transmission case.

Install the manual control lever shaft spring pin.
^ Tap the manual control lever shaft spring pin into the transmission case.





16. CAUTION: Align the flats on the manual valve inner lever with the flats on the manual control lever shaft.

Install the manual valve inner lever and parking lever actuating rod on to the manual control lever shaft.





17. CAUTION: To avoid damage, do not allow the wrench to strike the manual valve inner lever pin.

Install the manual valve inner lever nut on the manual control lever shaft and tighten.





18. CAUTION: The tabs on the output shaft thrust washer (No. 11) point into the case. Make sure the thrust washer is correctly seated.

Install the output shaft thrust washer (No. 11).
^ Coat the output shaft thrust washer with petroleum jelly.





19. Install the park gear.





20. Install the low/reverse brake drum.
^ Rotate the low/reverse brake drum clockwise to install.





21. If not already installed during subassembly, install the No. 10B needle bearing onto the output shaft ring gear and hub assembly.
^ Coat the needle bearing with petroleum jelly.





22. Install the output shaft through the output shaft park gear.





23. Install the output shaft ring gear and output shaft hub.





24. CAUTION: Always install a new output shaft retaining ring.

Install a new output shaft retaining ring.





25. NOTE: Install the output shaft sleeve with the cone facing up.

Install the output shaft sleeve.





26. Install low/reverse planetary carrier needle bearings.
1. Install low/reverse planetary carrier needle bearing (No. 8) on the front face of the low/reverse planetary.
2. Install low/reverse planetary carrier needle bearing (No. 9) on the rear face of the low/reverse planetary.
^ Coat the low/reverse planet carrier needle bearing (No. 8) and low/reverse planetary carrier needle bearing (No. 9) with petroleum jelly.





27. CAUTION: Make sure needle bearings stay in place.

Install the low/reverse planetary assembly with No. 8 and No. 9 low/reverse planetary carrier needle bearings into the output shaft ring gear.





28. CAUTION: The low/reverse brake drum must be pulled forward to install the low/reverse planet retaining ring.

Install the low/reverse retaining ring into the low/reverse brake drum groove.





29. CAUTION: Make sure band is resting on the two anchor pins in the case.

Install the low/reverse band over the low/reverse brake drum.





30. Temporarily install the low/reverse band servo piston and rod to hold the low/reverse band in position.





31. Install the previously assembled forward geartrain assembly.

32. WARNING: Make sure the lock pin on the special tool is secure. Failure to follow these instructions may result in personal injury.

Rotate transmission assembly so that the converter housing surface is facing up.





33. Select the intermediate brake drum thrust bearing (No. 4) as follows:
1. Install the special tool on case assembly shoulder.
2. Set the special tool on top as shown.





34. Calculate the thrust bearing thickness.
^ Extend the micrometer probe until it contacts the intermediate brake drum thrust bearing surface. Record the reading. This is dimension A.





35. Place the micrometer on the opposite side of the special tool and repeat measurement. This is dimension B.
36. Add dimension A and B. divide the total of A and B by 2. Then subtract the special tool thickness 17.78 mm (0.71 inch). Record this reading as dimension C.





37. Place the special tool across the center support. Place the micrometer on the top of the special tool.
1. Extend the micrometer probe until it makes contact with the center support thrust bearing surface. Record this reading as dimension D.





38. Place the special tool on the opposite side of the special tool.
1. Extend the micrometer probe until it makes contact with the center support thrust bearing surface. Record this reading as dimension F.





39. Add dimensions D and F. Divide the total of D and F by two. Subtract the special tool thickness 17.78 mm (0.71 inch) dimension E. The result is dimension G.





40. Add dimensions C and G. This total is dimension H. Use the following chart to select the correct No. 4 thrust bearing. Reference end play is 0.20 - 0.54 mm (0.008 - 0.021 inch).





41. Install the intermediate servo actuating lever.





42. NOTE: The intermediate band lever shaft is shorter than the front band lever shaft.

Install the intermediate band actuating lever shaft through the intermediate servo actuating lever.





43. Install the intermediate band apply strut on the intermediate servo actuating lever.





44. NOTE: Make sure that the intermediate apply strut is aligned with the band notch.

Install the intermediate band.





45. NOTE: Use the intermediate band adjusting screw as a temporary alignment guide.

NOTE: The intermediate and front band anchor struts and band adjustment screws are the same.

Install the intermediate band anchor strut and the intermediate band adjustment screw.





46. Install the selected intermediate brake drum thrust washer (No. 4) on the center support.
^ Coat the intermediate brake drum thrust washer with petroleum jelly.





47. CAUTION: Do not apply pressure to the center support while installing. Damage to sealing rings could result. Make sure the rear planetary support is seated.

NOTE: Align the center support screw hole with correct case hole.

Install the center support.
1. Position the center support into the intermediate brake and direct clutch drum.
2. Temporarily insert input shaft and gently wiggle it until the center support is seated against the case shoulder, then remove the input shaft.





48. CAUTION: Install the center support retaining ring with the tapered side facing up.

CAUTION: Make sure the notch opening is not obstructed by the center support retaining ring.

Install the center support retaining ring.
1. Position center support retaining ring with the tapered side facing up.
2. Install the center support retaining ring so that the notch opening is not obstructed.





49. Install the center support locknut and cage.





50. Install the center support-to-case capscrew.





51. CAUTION: Carefully route the turbine shaft speed (TSS) sensor connector and wiring harness through the opening in the case. Do not damage the wiring.

NOTE: Route TSS sensor electrical connector and wiring through transmission case opening.

Install the Turbine Shaft Speed (TSS) sensor.
1. Install the TSS sensor.
2. Install TSS sensor screw.





52. CAUTION: Use only the center shaft thrust bearing (No. 3).

NOTE: The center shaft thrust bearing (No. 3) has no notches on the outer race.

Install the center shaft thrust bearing (No. 3).





53. CAUTION: Do not bend the trigger wheel.

Install the front planetary carrier, front ring gear, front one-way clutch and center shaft assembly.





54. CAUTION: The trigger wheel triggering window should pass over the thin blade of the special tool. If it does not, the installation of a new front planetary carrier and trigger wheel will need to be carried out.

Using the special tool, check TSS sensor air gap.
1. Place the thin blade of the special tool over the TSS sensor.
2. Rotate the trigger wheel and repeat checks for all windows.





55. CAUTION: The trigger wheel triggering window should not pass over the thick blade of the special tool. If it does not, the installation of a new front planetary carrier and trigger wheel will need to be carried out.

Using the special tool, check TSS sensor air gap.
1. Place the thick blade of the special tool over the TSS sensor.
2. Rotate the trigger wheel and repeat checks for all windows.





56. NOTE: Align the clutch plates and front adapter gear.

Install the front brake drum and coast clutch drum assembly.





57. Install the front servo band lever and front band lever-to-case bracket into the transmission case.





58. NOTE: The front band lever shaft is longer than the intermediate band actuating lever shaft.

Install the front band actuating lever shaft through the front servo band lever.





59. Install the front band apply strut.





60. NOTE: If the front band is reused, it must be installed in the same position as when removed.

Install the front band over the front brake and coast clutch drum.





61. NOTE: Use the band adjustment screw as a temporary alignment guide.