Torque
| Valve cover bolts | 89 inch lbs. | |
| Camshaft bearing cap bolts | 89 inch lbs. | |
| Camshaft sprocket bolts | M10 bolt: Stage 1 | 30 ft. lbs. |
| Stage 2 | 90° | |
| M12 bolt | 90 ft. lbs | |
| Cylinder head temperature sensor (CHT) | 19 ft. lbs. | |
| Camshaft position sensor bolt | 89 inch lbs. | |
| Crankshaft position sensor bolt | 89 inch lbs. | |
| Connecting rod bolts | Stage 1 | 32 ft. lbs. |
| Stage 2 | 90-120° | |
| Crankshaft damper pulley bolt | Stage 1 | 66 ft.lbs. |
| Stage 2 | Loosen the bolt. | |
| Stage 3 | 37 ft. lbs. | |
| Stage 4 | 85 - 90 degrees. | |
| Crankshaft main bearing bolts (vertical) | Stage 1 | 30 ft. lbs. |
| Stage 2 | 85-95 degrees | |
| Crankshaft main bearing bolts (side) | Stage 1 | 22 ft.lbs. |
| Stage 2 | 85-95 degrees | |
| Cylinder head bolts LH The cylinder head bolts must be discarded and new bolts installed. They are tighten-to-yield designed and cannot be reused. | Stage 1 | 30 ft. lbs. |
| Stage 2 | 85-95 degrees | |
| Stage 3 | 85-95 degrees | |
| Cylinder head bolts RH The cylinder head bolts must be discarded and new bolts installed. They are tighten-to-yield designed and cannot be reused. | Stage 1 | 30 ft. lbs. |
| Stage 2 | 85-95 degrees | |
| Stage 3 | 85-95 degrees | |
| EGR valve to intake manifold bolts | Upper | 30-44 ft. lbs. |
| Lower | 30-44 ft. lbs. | |
| Exhaust manifold nuts | 18 ft. lbs. | |
| Exhaust manifold studs | 9 ft. lbs. | |
| Drive belt idler pulley bolt | 18 ft. lbs. | |
| Flywheel bolts | 59 ft. lbs. | |
| Engine front cover | bolts (1-5) | 18 ft. lbs. |
| bolts (6-15) | 35 ft. lbs. | |
| Fuel injection supply manifold bracket bolts | 89 inch lbs. | |
| Heater return tube studs | 30 ft. lbs. | |
| Ignition coil | 53 inch lbs. | |
| Intake manifold bolts | Stage 1 | 18 inch lbs. |
| Stage 2 | 18 ft. lbs. | |
| Knock sensor | 15 ft. lbs. | |
| Remote oil cooler line to cylinder block | 89 inch lbs. | |
| Oil cooler assembly to oil filter adapter bolts | 43 ft. lbs. | |
| Oil filter | 12 ft. lbs. | |
| Oil filter adapter bolt | 18 ft. lbs. | |
| Oil filter adapter nut | 35 ft. lbs. | |
| Oil filter adapter stud | 9 ft. lbs. | |
| Oil level indicator tube bolt | 89 inch lbs. | |
| Oil line connector adapter assembly bolt | 18 ft. lbs. | |
| Oil pan bolts | Stage 1 | 18 inch lbs. |
| Stage 2 | 15 inch lbs. | |
| Stage 3 | 90 degrees | |
| Oil pan drain plug | 10 ft. lbs. | |
| Oil pressure switch | 10 ft. lbs. | |
| Oil pump bolts | 89 inch lbs. | |
| Oil pump screen and pickup tube bolts | 89 inch lbs. | |
| Oil pump screen and pickup tube spacer | 18 ft. lbs. | |
| Oil pump screen and pickup tube spacer bolt | 18 ft. lbs. | |
| Power steering pump bolts | 18 ft. lbs. | |
| Rear main oil seal retainer bolts | 89 inch lbs. | |
| Spark plugs | 89 inch lbs. | |
| Thermostat housing bolts | 18 ft. lbs. | |
| Timing chain guide bolts | 89 inch lbs. | |
| Timing chain hydraulic tensioner bolts | 18 ft. lbs. | |
| Water pump bolts | 18 ft. lbs. | |
| Water pump pulley bolts | 18 ft. lbs. | |
| EGR valve to exhaust manifold tube fittings | 30-44 ft. lbs. | |
| 42-pin bulkhead connector bolts | 44 inch lbs. | |
| Accelerator control splash shield bolts | 62 inch lbs. | |
| Remote oil filter adapter line bolts (4x4 vehicles) | 89 inch lbs. | |
| Oil cooler insert | 43 ft. lbs. | |
| Oil cooler bolt (4x4 vehicles) | 43 ft. lbs. | |
| Motor mount bolts | 59 ft. lbs. | |
| Fan shroud bolts | 80 inch lbs. | |
| Differential pressure feedback EGR system nuts | 89 inch lbs. | |
| Exhaust-to-manifold EGR valve tube | 30-44 ft. lbs. | |
| Radio ignition interference capacitor nuts | 18 ft. lbs. | |
| Transmission-to-engine bolts | 35 ft. lbs. | |
| Torque converter-to-flexplate nuts | 26 ft. lbs. | |
| Generator upper mounting bracket bolts | 89 inch lbs. | |
| Generator lower mounting bolts | 18 ft. lbs. |