Oil Pan: Service and Repair
Oil PanSpecial Tool(s):
Material:
Removal
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
2. Remove the engine cover.
3. Remove the intake manifold.
4. Remove the engine cooling fan and fan shroud. For additional information, refer to Cooling System.
5. Remove the retainers and the shield.
6. Remove the stud bolts and position the heater outlet tube aside.
7. Remove the 2 transmission-to-engine bolts.
8. Disconnect the oil fill tube from the RH valve cover.
9. Remove the bolt and the oil fill tube.
10. Assemble the special tools.
11. Install the special tools.
12. Install the special tool and support the engine.
13. Drain the engine oil and remove the oil filter.
14. Remove the nut and position the transmission fluid cooler tube support bracket aside.
15. NOTE: RH shown, LH similar.
Remove the 4 engine support insulator nuts.
16. Remove the flywheel inspection plate.
17. Using the special tool, raise the engine.
18. Remove the bolts and partially lower the oil pan.
19. Remove the bolts retaining the oil pump screen and pickup tube and allow it to drop into the oil pan. Also remove the tube and spacer and allow it to drop into the oil pan. Remove the oil pan.
^ Discard the oil pan gasket.
20. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These may cause scratches and gouges resulting in leak paths. Use a plastic scraper to clean the sealing surfaces.
Clean the sealing surfaces with silicone gasket remover and metal surface prep. Follow the directions on the packaging. Inspect the mating surfaces.
Installation
1. NOTE: The oil pump screen and pickup tube must be in the oil pan when the oil pan is positioned in the vehicle.
Position the new oil pan gasket and the oil pan in the vehicle from the rear of the engine.
2. Position the oil pump screen and pickup tube and the 3 bolts into the oil pan and position the oil pan and new oil pan gasket onto the crossmember.
3. CAUTION: Make sure the O-ring is in place and not damaged. A missing or damaged O-ring can cause foam in the lubrication system, low oil pressure and severe engine damage.
NOTE: Clean and inspect the mating surfaces and install a new O-ring. Lubricate the O-ring with clean engine oil.
Position the oil pump screen and pickup tube and install the 3 bolts.
^ Tighten the 2 oil pump screen and pickup tube-to-oil pump bolts to 10 Nm (89 inch lbs).
^ Tighten the oil pump screen and pickup tube-to-spacer bolt to 25 Nm (18 ft. lbs).
4. NOTE: If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Allow to dry until there is no sign of wetness, or 4 minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
Apply the silicone gasket and sealant at the engine front cover-to-cylinder block mating surface.
5. NOTE: If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Allow to dry until there is no sign of wetness, or 4 minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
Apply silicone gasket and sealant in the locations shown.
6. Tighten the bolts in 3 stages, in the sequence shown.
^ Stage 1: Tighten to 2 Nm (18 inch lbs).
^ Stage 2: Tighten to 20 Nm (15 ft. lbs).
^ Stage 3: Tighten an additional 60 degrees.
7. Lower the engine and remove the special tools.
8. Position the flywheel inspection plate and install the 2 bolts.
^ Tighten to 34 Nm (25 ft. lbs).
9. Install the engine support insulator nuts.
^ Tighten to 90 Nm (66 ft. lbs).
10. Position the transmission fluid cooler tube support bracket and install the nut.
^ Tighten to 30 Nm (22 ft. lbs).
11. Install the new oil filter.
^ Tighten to 16 Nm (12 ft. lbs).
12. NOTE: Do not reuse the O-ring seal.
Install the new O-ring seal and the heater outlet tube.
^ Lubricate the O-ring seal with engine coolant.
13. Hand-tighten the heater outlet tube upper stud and install the lower stud.
^ Tighten to 40 Nm (30 ft. lbs).
14. Connect the oil fill tube to the RH valve cover.
15. Install the oil fill tube support bracket bolt.
^ Tighten to 10 Nm (89 inch lbs).
16. Install the transmission-to-engine bolts.
^ Tighten to 47 Nm (35 ft. lbs).
17. Install the shield and the retainers.
18. Install the intake manifold.
19. Install the engine cover.
20. Fill the engine with clean engine oil.
21. Install the engine cooling fan and fan shroud.
22. Fill and bleed the engine cooling system.